background image

5A–1

BRAKE CONTROL SYSTEM

RODEO

BRAKES

CONTENTS

Brake Control System

5A–1

. . . . . . . . . . . . . . . . . . . . 

Anti–lock Brake System

5B–1

. . . . . . . . . . . . . . . . . . 

Power–assisted Brake System

5C–1

. . . . . . . . . . . . 

Parking Brakes (4x4 Model)

5D1–1

. . . . . . . . . . . . . . 

Parking Brakes (4x2 Model)

5D2–1

. . . . . . . . . . . . . . 

Brake Control System

CONTENTS

Service Precaution

5A–2

. . . . . . . . . . . . . . . . . . . . . . 

General Description

5A–3

. . . . . . . . . . . . . . . . . . . . . 

Functional Description

5A–4

. . . . . . . . . . . . . . . . . 

System Components

5A–10

. . . . . . . . . . . . . . . . . . . 

Electronic Hydraulic Control Unit (EHCU)

5A–10

ABS Warning Light

5A–10

. . . . . . . . . . . . . . . . . . . . 

Wheel Speed Sensor

5A–10

. . . . . . . . . . . . . . . . . . 

G-Sensor

5A–10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Normal and Anti-lock Braking

5A–10

. . . . . . . . . . . 

Brake Pedal Travel

5A–10

. . . . . . . . . . . . . . . . . . . . 

Acronyms and Abbreviations

5A–10

. . . . . . . . . . . . 

General Diagnosis

5A–11

. . . . . . . . . . . . . . . . . . . . . . . 

General Information

5A–11

. . . . . . . . . . . . . . . . . . . . 

ABS Service Precautions

5A–11

. . . . . . . . . . . . . . . 

Computer System Service Precautions

5A–11

. . . 

General Service Precautions

5A–11

. . . . . . . . . . . . 

Note on Intermittents

5A–11

. . . . . . . . . . . . . . . . . . . 

Test Driving ABS Complaint Vehicles

5A–12

. . . . . 

“ABS” Warning Light

5A–12

. . . . . . . . . . . . . . . . . . . 

Normal Operation

5A–12

. . . . . . . . . . . . . . . . . . . . . 

Tech 2 Scan Tool

5A–13

. . . . . . . . . . . . . . . . . . . . . . 

DATA LIST

5A–16

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

ACTUATOR TEST

5A–17

. . . . . . . . . . . . . . . . . . . . . 

Tech 2 Service Bleed

5A–21

. . . . . . . . . . . . . . . . . . 

Basic Diagnostic Flow Chart

5A–22

. . . . . . . . . . . . 

Basic Inspection Procedure

5A–23

. . . . . . . . . . . . . 

EHCU Connector Pin-out Checks

5A–24

. . . . . . . . . 

Circuit Diagram

5A–25

. . . . . . . . . . . . . . . . . . . . . . . 

Connector List

5A–28

. . . . . . . . . . . . . . . . . . . . . . . . 

Part Location

5A–29

. . . . . . . . . . . . . . . . . . . . . . . . . 

Symptom Diagnosis

5A–30

. . . . . . . . . . . . . . . . . . . . . 

Chart A-1 ABS Works Frequently But
 Vehicle Does Not Decelerate

5A–30

. . . . . . . . . . . 

Chart TA-1 ABS Works Frequently But
 Vehicle Does Not Decelerate
 (Use TECH 2)

5A–31

. . . . . . . . . . . . . . . . . . . . . . . . 

Chart A-2 Uneven Braking Occurs While
 ABS Works

5A–31

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Chart TA-2 Uneven Braking Occurs While
 ABS Works (Use TECH 2)

5A–31

. . . . . . . . . . . . . 

Chart A-3, TA-3  The Wheels Are Locked

5A–32

Chart A-4 Brake Pedal Feed Is Abnormal

5A–33

Chart A-5, TA-5 Braking Sound
 (From EHCU) Is Heard While Not Braking

5A–34

Diagnostic Trouble Codes

5A–35

. . . . . . . . . . . . . . . . 

Diagnosis By “ABS” Warning Light
 Illumination Pattern

5A–37

. . . . . . . . . . . . . . . . . . . . . 

Diagnostic Trouble Codes (DTCs)

5A–38

. . . . . . . 

Chart B-1 With the key in the ON position
 (Before starting the engine).  Warning
 light (W/L) is not activated.

5A–40

. . . . . . . . . . . . . 

Chart B-2 CPU Error (DTC 14 (Flash out) /
 C0271, C0272, C0273, C0284 (Serial
 communications))

5A–41

. . . . . . . . . . . . . . . . . . . . . 

Chart B-3 Low or High Ignition Voltage
 (DTC 15 (Flash out) / C0277, 0278
 (Serial communications))

5A–41

. . . . . . . . . . . . . . . 

Chart B-4 Excessive Dump Time
 (DTC 17 (Flash out) / C0269
 (Serial communications))

5A–41

. . . . . . . . . . . . . . . 

Chart B-5 Excessive Isolation Time
 (DTC 18 (Flash out) / C0274
 (Serial communications))

5A–42

. . . . . . . . . . . . . . . 

Chart B-6 G-Sensor Output Failure
 (DTC 21 (Flash out) / C0276
 (Serial communications))

5A–42

. . . . . . . . . . . . . . . 

Chart B-7 Brake Switch Failure
 (DTC 22 (Flash out) / C0281
 (Serial communications))

5A–42

. . . . . . . . . . . . . . . 

Chart B-8 2WD Controller in 4WD Vehicle
 Controller (DTC 13 (Flash out) / C0285
 (Serial communications)), 4WD State Input
 Signal Failure (DTC 24 (Flash out) / C0282
 (Serial communications))

5A–43

. . . . . . . . . . . . . . . 

Chart B-9 Pump Motor Failure (DTC 32
 (Flash out) / C0267, C0268
 (Serial communications))

5A–43

. . . . . . . . . . . . . . . 

Chart B-10 EHCU Valve Relay Failure
 (DTC 35 (Flash out) / C0265, C0266
 (Serial communications))

5A–44

. . . . . . . . . . . . . . . 

Chart B-11 FL Isolation Solenoid Coil Failure
 (DTC 41 (Flash out) / C0245, C0247
 (Serial communications))

5A–44

. . . . . . . . . . . . . . . 

Chart B-12 FL Dump Solenoid Coil Failure
 (DTC 42 (Flash out) / C0246, C0248
 (Serial communications))

5A–44

. . . . . . . . . . . . . . . 

Содержание 1999 RODEO


























































Отзывы: