manualshive.com logo in svg

Isotech Pegasus R 970, Руководство по эксплуатации пользователя, Страница: 11 / 24

Поделиться
Скачать
Isotech Pegasus R 970 Скачать руководство пользователя страница 11

 

Page 11 of 24 

Pegasus R Iss.07 – 08/13 

CALIBRATION USING THE TEMPERATURE INDICATED ON THE 
CONTROLLER 

 

1. 

Remove the Pegasus 'R' from its case and visually inspect it for any damage it may have sustained since it was 

last used.  Insert the black body source assembly (see fig 970-20-02) into the furnace tube with the ceramic 

insulators.   

 

2. 

Connect the Pegasus 'R' to a suitable power supply and set the controller to the required temperature (see 

the controller's manual for details and Fig 1). 

 

3. 

Wait for the temperature to stabilise. 

 

4. 

When the temperature indicated by the controller and the output of the thermometer are both stable (see 

specification for typical values) record three sets of readings over a period of about six minutes.  Check that 

these readings are consistent and then calculate their average values. 

 

5. 

The Pegasus 'R' has itself been calibrated, correct the average values accordingly.   

 

6. 

Reset the controller and/or repeat the calibration for another thermometer. 

 
7. 

When the calibration is complete, reset the controller to 0 C and wait until the unit has cooled to below 
400 C before moving the Pegasus to a new location.  The Pegasus must be cooled to about 100 C before it 

can be put back into its carrying case.  

 

 

 

 

Содержание Pegasus R 970

























Отзывы:

Нет отзывов