Isotech M17705 Скачать руководство пользователя

Страница: 4 / 40

Page 4 of 40

Dual Furnace Models M17705, N17706 & 17707 Iss.09 – 12/14

EMC INFORMATION

This product meets the requirements of the European Directive on Electromagnetic Compatibility (EMC)

89/336/EEC as amended by EC Directive 92/31/EEC and the European Low Voltage Directive 73/25/EEC, amended

by 93/68/EEC. To ensure emission compliance please ensure that any serial communications connecting leads are

fully screened.

The product meets the susceptibility requirements of EN 50082-1, criterion B.

Symbol Identification

Publication

Description

ISO3864

Caution (refer to manual)

IEC 417

Caution, Hot Surface

ELECTRICAL SAFETY

This equipment must be correctly earthed.

This equipment is a Class 1 Appliance. A protective earth is used to ensure the conductive parts cannot become live

in the event of a failure of the insulation.

The protective conductor of the flexible mains cable which is coloured green/yellow MUST be connected to a

suitable earth.

The Blue conductor should be connected to Neutral and the Brown conductor to Live (Line).

Warning: Internal mains voltage hazard. Do not remove the panels.

There are no user serviceable parts inside. Contact your nearest Isotech agent for repair.

Voltage transients on the supply must not exceed 2.5kV.

Conductive pollution, e.g. Carbon dust, must be excluded from the apparatus. EN61010 pollution degree 2.

Содержание M17705









































Результаты поиска

Содержание M17705

Отзывы:

Похожие инструкции для M17705

Бренды по названию

Популярные бренды

Isotech M17705, Руководство по эксплуатации пользователя

Результаты поиска

Содержание M17705

Отзывы:

Похожие инструкции для M17705

Бренды по названию

Популярные бренды