Isotech ITL- M-17702 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 37

background image

HIGH TEMPERATURE

FURNACE HANDBOOK

ISSUE 8 - 05/05

Page 4 of 37

mailto:[email protected]

EMC INFORMATION

This  product  meets  the  requirements  of  the  European  Directive  on  Electromagnetic
Compatibility  (EMC)  89/336/EEC  as  amended  by  EC  Directive  92/31/EEC.    To  ensure
emission  compliance  please  ensure  that  any  serial  communications  connecting  leads
(RS232 or RS422 or 485) are fully screened.

The  product  meets  the  susceptibility
requirements of EN 50082-1, criterion
C.

ELECTRICAL SAFETY

This equipment must be correctly earthed.

This equipment is a Class 1 Appliance.  A protective earth is used to ensure the conductive
parts cannot become live in the event of a failure of the insulation.

The  protective  conductor  of  the  flexible  mains  cable  which  is  coloured  green/yellow  MUST
be connected to a suitable earth.

The Blue conductor should be connected to Neutral and the Brown conductor to Live (Line).

Warning: Internal mains voltage hazard.  Do not remove the panels.

There are no user serviceable parts inside.  Contact your nearest Isotech agent for repair.

Voltage transients on the supply must not exceed 2.5kV.

«
...
2
3
4
5
6
...
»

Содержание ITL- M-17702






































Отзывы:

Нет отзывов

Похожие инструкции для ITL- M-17702

Бренд: American Standard Страницы: 4

Бренд: CLEAN BURN Страницы: 142

Vulcan Box A-130

Бренд: DENTSPLY Страницы: 12

Бренд: Lenoxx Страницы: 36

Бренд: DAKA Страницы: 12

Бренд: York Страницы: 8

Бренд: York Страницы: 40

Бренд: Bard Страницы: 53

Бренд: KING Страницы: 6

FEM10-M2301CM-A

Бренд: SUPREME Страницы: 40

SIGNATURE SLP99DF070V36

Бренд: Lennox Страницы: 71

Бренд: Lifebreath Страницы: 42

Бренд: IKL Страницы: 19

Бренд: Lennox Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды