background image

 

5- 

  2. Technical Specification 

 

 

 Power supply 

- AC 120V~60Hz or AC 230/240/250V~50/60Hz 

   

Light Source   

- MSD 250W/ NSD 250/2 W 
- LED: Total 12pcs, Red: 4pcs, Green: 4pcs, Blue: 4pcs 

 

 Optical system 

- High efficiency optical system 
- High quality optical lens and dichroic colors 
- Beam angle: 13

°

 

 

 Shutter/Dimmer 

- Blackout, 0~100 smooth dimming and strobe speed variable(1~10 flashes per 

second). 

 

 Color wheel 

- Independent color wheel with 9 trapezoid dichroic colors plus white. 
- Color wheel rotates with variable speed, giving rainbow effect. 

Gobo wheel 

- Independent gobo wheel with 7 rotating, interchangeable gobos plus open: 5 metal 

gobos, 2 glass gobos are included. 

- Gobo wheel rotates with variable speed, giving shaking effect. 

Effect Wheel 

- Prism/Rotating Prism 

 

 Movement 

- Pan: 540° in 2.8 second. 
- Tilt: 270° in 1.6 second.   

 

 DMX Channels 

Channel 1 = Pan   

Channel 12 = Prism Rotation 

Channel 2 = Tilt   

Channel 13 = Focus 

Channel 3 = Pan/Tilt Speed selection  Channel 14 = Pan 16 bit 
Channel 4 = Dimmer 

Channel 15 = Tilt 16 bit 

Channel 5 = Shutter/Shaking 

Channel 16 = Reset/Lamp on/off 

Channel 6 = Color 

Channel 17 = Red LED 

Channel 7 = No Function 

Channel 18 = Green LED 

Channel 8 = No Function 

Channel 19 = Blue LED 

Channel 9 = Gobo   

Channel 20 = LED Color Macro 

Channel 10 = Gobo Rotation 

Channel 21 = Dimmer/Strobe 

Channel 11 = Prism 

 

 

22- 

Pay attention to the belt tension when install the belt. 

 

Please refer to the photos below:   

 

Photo 1 

 

Photo 2 

Содержание IM-250SW















Отзывы: