manualshive.com logo in svg

Isokern STANDARD 36, Руководство пользователя

Поделиться
Скачать
Isokern STANDARD 36 Скачать руководство пользователя страница 37

37

DM 54 Chimney System: Brick Ledge Installation

FIGURE 64

 

Consult local structural engineer for proper job-spe-

cific support structure design, sizing and load bearing specifi

-

cations.

 

 

If short lengths of steel rods are used be sure to properly 

lap and wire tie all splices in the rebar. As the reinforcing pro

-

gresses, completely fill the holes with grout. Suitable grout can 

be a pourable mixture of Portland cement and sand or Portland 

cement, sand and pea gravel. The rebar must be fully embedded in 

grout.

 

Leave enough of the #4 steel reinforcing rod exposed 

above the brickledge so that as the stacking of outer casing blocks 

continues to termination the reinforcing rods and grout can con-

tinue through the stack. Reinforcing shall continue to chimney 

termination.

 

All DM 54 chimneys that include the DM 54 brickledge 

must be reinforced as described above.

CAUTION:

 When using the Isokern brickledge it is required that 

the Standard firebox/smoke dome assembly include the placement 

of a 4” by  4” by 3/8” minimum steel angle across the firebox 

opening. (See page 41 for “Structural Information” for details 

regarding specification and placement of steel angles in Standard 

fireplaces.)

Lateral Support for Isokern Brickledge Chimneys:

 

Once the DM 54 chimney and brickledge are assembled 

and after the intended masonry veneer has been installed on the 

brickledge, be sure to brace the chimney following the guidelines 

on pages 31 & 32 of this manual for Lateral Support of DM 54 

chimneys.

Содержание STANDARD 36




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды