Islandaire EZ07 Скачать руководство пользователя страница 21

Страница: 21 / 60

Manufacturer of Quality Air Conditioning and Heating Products • www.islandaire.com • sales@islandaire.com • (800)-886-2759

Wall Sleeve Installation Instructions (

cont.

)

block Wall Application

The wall sleeve will need to be installed so that the sleeve

projects into the room a minimum of 1.25 inches and a

maximum of 11.5 inches.

The wall sleeve will need to be installed so that the sleeve

projects beyond the exterior wall a minimum of 0.25

inches.

When installed in the appropriate wall sleeve, this appli-

ance has zero clearance to combustible construction.

The minimum required clearance distance between the

wall sleeve and finished floor is 3.0 inches. Wall sleeve

installations that project into the room 4.5” or more

require the use of Leveling Legs or other means of sup-

porting the wall sleeve.

Block Wall Installation

Secure the wall sleeve to the surrounding studs by

drilling two 1/8 inch diameter holes through both sides

approximately in the center of studs using 3⁄4 inch pan

head type screws supplied. Shim if necessary to prevent

the sleeve from bowing. Make sure the wall sleeve is level

from side-to-side and sloped 1⁄4 inch from front-to-rear.

DO NOT DRILL HOLES IN THE BOTTOM OF THE

SLEEVE, WATER DAMAGE WILL OCCUR.

Seal around the outside portion of the wall sleeve using

weatherproof caulking to form a seal against rain, snow,

and air leakage.

CAUTION

Do not slope the wall sleeve toward the room.

“X” = 1 1/4” MIN. - 11 1/2” MAX.

SUBBASE REQUIRED WHEN 4 1/2”
OR MORE

SURFACE OF FINISHED

INTERIOR WALL

CABINET

FRONT

SURFACE OF FINISHED

FLOOR OR CARPET

SURFACE OF FINISHED

EXTERIOR WALL

CAULK ALL AROUND

WALL SLEEVE

REAR GRILLE

MOUNTING HOLES AND SCREWS (BY

INSTALLER)

DO NOT PUT HOLES THROUGH

BOTTOM OF WALL SLEEVE

1/4” SLOPE DOWN TO

THE OUTSIDE

1/4” MIN. PROJECTION BEYOND

EXTERIOR WALL

Front View

Make sure wall sleeve is level side-to-side

FASTEN SLEEVE

TO FRAMING WITH

WOOD SCREWS AT

SIDES & TOP

DO NOT DRILL OR ATTACH SCREWS TO

BOTTOM OF SLEEVE

Side View

INSIDE WALL

SEE NOTE 4

X”

3” MIN.

“

Figure 7

Block Wall Sleeve Installation

Содержание EZ07





























































Результаты поиска

Содержание EZ07

Отзывы:

Похожие инструкции для EZ07

Бренды по названию

Популярные бренды

Islandaire EZ07, Инструкция по эксплуатации

Результаты поиска

Содержание EZ07

Отзывы:

Похожие инструкции для EZ07

Бренды по названию

Популярные бренды