S p e z i a l e l e k t r o n i k G m b H
iseg Spezialelektronik GmbH
Email: [email protected]
Phone ++ 49 (0)351 / 26 996 - 0
Bautzner Landstr 23
http://www.iseg-hv.com
Fax
++ 49 (0)351 / 26 996 - 21
D - 01454 Radeberg / Rossendorf
Germany
3
Female H15 - connector on the back plane for the HV module
PIN
Name
Male H15 - connector / Description
8 V
REF
V
8-10/12
= 5 V ( 1 mA) Internal reference voltage for an external potentiometer
(Sliding contact on V_V
SET
or V_I
SET
))
10/12 PWR_0V
Power_0 V (internal connected with HV-GND = LOW-potential)
14 V_I
MON
Monitor voltage corresponding I
OUT
:
I
OUT
= 0 to I
OUTmax
±
1 %
⇒
V
14-10/12
= 0 to 5 V
20 V_V
SET
Setting voltage: V
20-10/12
= 0 to 5 V
⇒
V
OUT
= 0 to V
OUTmax
±
1 %
22 POL
Polarity switching (TTL level):
open or High-level
⇒
positive,
Low-level
⇒
negative
24 V_V
MON
Monitor voltage corresponding V
OUT
: V
OUT
= 0 to V
OUTmax
±
1 %
⇒
V
24-10/12
= 0 to 5 V
26 PWR_+V V
26-10/12
= + 24 V-DC
±
5% / max. 0,8 A
28 V_I
SET
Setting current:
V
28-10/12
= 0 to 5 V
⇒
I
OUT
= 0 to I
OUTmax
±
1 %
(connected with V
REF
through 10 k
Ω
)
n.c.:
I
OUTmax
is possible
30 KILL_ENA TTL-level, High = active
⇒
HV_OFF without ramp if signal INHIBIT is active.
Restoring the output voltage is only possible after operating KILL_ENA or PWR_ON.
LOW (or n.c.)
⇒
HV according V_V
SET
or V_I
SET
, limited to V
max
, I
max
resp.
32 INHIBIT TTL-level, LOW = active
⇒
V
OUT
= 0
HIGH (or n.c.)
⇒
V
OUT
according V_V
SET
(with ramp)
Female 96-pin connector for the universal interface board in the crate ECH 128
H15-slots from 0 (left ) to 7 (right) 96-pin connector for
Multichannel CAN I/O (rightmost)
VS0 to VS7: V_v-set for slots 0 to 7 (H15: 20)
IS0 to IS7: V_i-set for slots 0 to 7 (H15: 28)
VM0 to VM7: V_v-mon for slots 0 to 7 (H15: 24)
IM0 to IM7: V_i-mon for slots 0 to 7 (H15: 14)
KILLEN : KILL_ENA for slots 0 to 7 (H15: 30)
+24 V: PWR_+V for slots 0 to 7 (H15: 26)
GND: PWR_0V for slots 0 to 7 (H15: 10/12)
DB0 to DB7: POL for slots 0 to 7 (H15: 22)
