Isee IGEP v2 Скачать руководство пользователя страница 6

Страница: 6 / 66

IGEP

Hardware Reference Manual

™

is a registered trademar k from ISEE 2007 S.L. The followi ng is provided for informational purpos es onl y.

DOCUMENT FROM ISEE 2007 S.L. Ref: MAN-PR-IGEP0020-RCx

OVERVIEW

4.1

ABOUT THIS MANUAL

This manual describes IGEP

™

v2 hardware features. IGEP

™

v2 is an IGEP

™

technology device

from ISEE. You can find additional information at our website

The

chapter describes general features of this base board and show the block

diagram. The

“

5 ON-BOARD DEVICES & INTERFACES

”

chapter describes in more detail each

device and interface connectors included on this product.

“

6 EXPANSION CONNECTOR J990:

GPIO

”

chapter describes in detail the function of each pin of the expansion connector included

on the board. 8 MECHANICAL SPECIFICATIONS chapter describes the mechanical
characteristics of the product and finally chapter 9 ELECTRICAL CHARACTERISTICS show a table
with the electrical specifications of the product.

At the end of this document you will find a list of tables, figures and change log. You will find

these elements in chapters: “

” and “

4.2

IGEP

™

v2 DESCRIPTION

IGEP

™

v2 is an embedded processor development board based on Texas Instruments

OMAP3530/DM3730 processor.

Texas Instruments OMAP3530/DM3730 processor @720MHz/1GHz

DSP TMS320DM-C64+ 500 MHz / 800 MHz

NEON SIMD Coprocessor

Video Acceleration

Camera Interface

RAM 512 MBytes LPDDR SDRAM

–

200 MHz

NAND Flash 512 Mbytes

On board micro-SD socket

Debug RS232 & JTAG

Connection to 5V power supply.

Designed for industrial and commercial purposes.

USB OTG 2.0 on mini AB connector

USB HOST 2.0 HS

Содержание IGEP v2



































































Результаты поиска

Содержание IGEP v2

Отзывы:

Бренды по названию

Популярные бренды

Isee IGEP v2, Справочник по аппаратуре

Результаты поиска

Содержание IGEP v2

Отзывы:

Бренды по названию

Популярные бренды