iRZ ES75iT Скачать руководство пользователя страница 19

 

 

19 

 

4.  Emergencies 

To facilitate the use of the modem tracking and indication of emergencies is provided.  

4.1.  Emergency 1 (incorrect input power supply) 

Emergency 1 occurs when the input power supply deviates from the permissible value. The modem stops 

working and it shuts down the GSM module power. A permanent red LED signals that the emergency has 

occurred. The recovery is possible only when the input power supply is re-established.  

4.2.  Emergency 2 (incorrect module power supply) 

Emergency 2 occurs when the GSM module power supply deviates from the permissible value. The modem 

stops working and it shuts off the GSM module power. A red LED signals that the emergency has occurred 

(0.5s on / 0.5s off). The recovery is possible only if the module power supply is re-established within 10 

seconds after the emergency occurred. If within 10 seconds the module power supply remains incorrect (with a 

correct input power supply), the modem goes into the waiting mode meaning that the modem’s power supply is 

turned off, the emergency indication is preserved. The waiting mode can be terminated only after the power is 

completely disconnected.  

In case of repeated emergency, the modem should be serviced.  

4.3.  Emergency 3 (GSM module failed to start) 

Emergency 3 occurs if the GSM module does not turn on or is absent. A red LED signal (0.25s on / 0.25s 

off / 0.25s on / 1s off) turns on after a precise determination by the modem of the emergency situation (~15 

sec). The recovery is possible only after a successful launch of the GSM module. After 10 unsuccessful 

attempts to launch the module, the modem goes into the waiting mode meaning that the modem’s power 

supply is turned off, the emergency indication is preserved. The waiting mode can be terminated only after the 

power is completely disconnected.  

In case of repeated emergency after the modem is turned back on, the modem should be serviced. 

4.4.  Emergency 4 (COM-port not ready) 

Emergency 4 occurs if COM-port of the GSM module is not ready. A red LED signals that the emergency 

has occurred (0.25s on/ 0.25s off/ 0.25s on / 0.25s off / 0.25s on / 1s off). The recovery depends on the 

readiness of the COM-port of the GSM module. After 10 unsuccessful attempts (20 seconds) the modem goes 

into the wait mode meaning that the modem’s power supply is turned off and the emergency indication is 

preserved. 

In case of repeated emergency after the modem is turned back on, the modem should be serviced. 

Содержание ES75iT





















Отзывы: