TO SET THE ALARM 2
* Press and hold the button for 3 seconds:
* The alarm2 hour digit will flash, then press
the
▲
button or the
▼
button to adjust to
the desired hour.
* Press the button, the alarm2 minute digit will
flash, then press the
▲
button or the
▼
button to
adjust to the desired minute.
* Press the button to show the current
snooze period with the minute field flashes.
* Press the
▲
button or the
▼
button to adjust
to the desired snooze period from 1 minute
to 59 minutes.
* Press the button and the alarm2 time is set and
enabled.
* If no key is pressed for 30 seconds, the clock will
resume the alarm 2 display.
TO SET THE DAILY ALARM 1
Press and hold the button for 3 seconds:
* The alarm1 hour digit will flash, then press
the button or the button to adjust to
the desired hour.
* Press the button, the alarm1 minute
digit will flash, then press the button or the
button to adjust to the desired minute.
* Press the button to show the current
snooze period with the minute field flashes.
* Press the button or the button to adjust
to the desired snooze period from 1 minute
to 59 minutes.
* Press the button and the alarm1 time is set and
enabled.
* If no key is pressed for 30 seconds, the clock will
resume the alarm l display.
1
1
1
1
1
2
2
2
2
RECEIVING THE RADIO CONTROL SIGNAL
The radio-controlled clock will automatically receive the radio signal
every hour. It will take 3-5 minutes to receive the radio signal.
If the DCF signal is received, the DCF tower will be visible on the
display, otherwise it will not.
BACKLIGHT
Moving your hand directly over the motion sensor up to 30 cm away to
illuminate the display for approximately 3 seconds.
LOW BATTERY LEVEL DETECTION
Should the battery capacity drop to a level that is not sufficient to operate
the clock, the low battery indicator will light up. The battery should be
replaced as soon as possible.
USING THE ALARM AND SNOOZE FOR DAILY
ALARM 1 or ALARM 2
* Press the / button to turn the alarm1 and alarm2 on and
off alternately.
* When the current time reaches the alarm time that is enabled, the
corresponding alarm is activated.
* Press the / button when the alarm is activated, it will stop for 24
hours.
* When the alarm is activated, move your hand directly over the motion
sensor and the alarm stops but sounds again after the snooze period
(4 minutes snooze period is pre-programmed).
* The repeat alarm indicator will flash.
* The alarm will stop after 4 minutes if the / button is not pressed
or the motion sensor is not triggered.
2
1
2
1
2
1
Attention!
Please dispose of used batteries
in an ecologically safe manner.
CARE OF THE DEVICE
- Do not expose the device to extreme temperatures or direct sunlight
over longer periods.
- Avoid blows and shocks of any kind to the device.
- For cleaning use a dry soft cloth that you have moistened with water
and a very mild cleaning agent. Never use volatile substances such as
benzene, thinner, cleansing agents in spray cans etc.
- When the device is not being used store it in a dry area and out of the
reach of small children. In such cases it is important to remove the
batteries!
- If the device is activated under extreme coldness it may occur that the
display becomes illegible. As soon as it is returned to a warm
environment the device will function normally again.
- Please keep the Instruction Manual and other documents delivered with
the device stored carefully so that you can reference them at a later
point if necessary.
- Important: All disposal fees in Switzerland (vRG) as well as in the EU
(WEEE) for all Irox devices are covered.
SUPPORT
This device is a new development of Irox Development Technology. All
information was made and checked by means of a functioning device. It
may occur that adjustments and improvements of the device will take
place that due to typographical procedures were not able to be listed in
this manual. Should you notice deviations which make it difficult for
you to operate and use of the device you may at any time download the
latest manual onto your PC free of charge at www.irox.com.
8
9
10
11
12