background image

Page 4 of 18 

 

Intended Use 

The Ironton 7 Inch Wet Tile Saw is designed for cutting ceramic and clay paving, wall tiles, slate, 
marble, granite, clay, and terracotta wall and floor tiles. 

Packaging Contents 

 

Tile Saw 

 

Blade Guard 

 

Water Tank 

 

Spanner 

 

Parallel Guide 

 

Rubber Feet 

 

Miter Gauge 

 

Saw Blade 

 

Owner’s 
Manual 

 

 

 

Technical Specifications 

Property 

Specification 

Motor 

110V / 60Hz / 3.75A (2/3 HP) 

Speed 

3600 RPM 

Max Cut Depth 

1 2/5 in. @ 90°, 1in. @ 45° 

Table Size 

15 in. x 15 1/2 in. 

Important Safety Information 

WARNING

 

 

Read and understand all instructions. Failure to follow all instructions may result in serious injury 
or property damage. 

 

The warnings, cautions, and instructions in this manual cannot cover all possible conditions or 
situations that could occur. Exercise common sense and caution when using this tool. Always be 
aware of the environment and ensure that the tool is used in a safe and responsible manner.  

 

Do not allow persons to operate or assemble the product until they have read this manual and 
have developed a thorough understanding of how it works. 

 

Do not modify this product in any way. Unauthorized modification may impair the function and/or 
safety and could affect the life of the product. There are specific applications for which the product 
was designed.  

 

Use the right tool for the job. DO NOT attempt to force small equipment to do the work of larger 
industrial equipment. There are certain applications for which this equipment was designed. This 
product will be safer and do a better job at the capacity for which it was intended. DO NOT use 
this equipment for a purpose for which it was not intended. 

 

Industrial or commercial applications must follow OSHA requirements. 

 

WARNING

 

WORK AREA SAFETY 

Содержание 61450



















Отзывы: