iQe RT322 Скачать руководство пользователя страница 4

Battery replacement

The RT322 runs on 2 x type AAA (Alkaline) non rechargeable batteries and is designed to 
give a battery life of approximately two years. 

When the batteries are nearing the end of their life a 
low battery symbol will appear in the display and the 
batteries should be changed within a few days. If the 
batteries are not changed at this point eventually a 
‘LO’  battery  message  flashes  intermittently  in  the 
display and if this happens the batteries should be 
changed immediately.

To change the batteries it is necessary to remove the thermostat from the wall. To do this 
first undo the two captive screws at the base of the thermostat and swing the thermostat 
up and away from the wall plate.

Remove the old batteries and replace them with two new AAA 
size alkaline batteries ensuring that they are fitted correctly as 
indicated by the terminal markings in the battery compartments.

Once the batteries are fitted, re-fit the thermostat to the wall plate 
by engaging with the lugs at the top of the wall plate and push the 
thermostat into position. Locate it over the captive screws at the 
base of the wall plate and tighten so that the thermostat is locked 
into position.

Check the temperature setting is correct and adjust if necessary.

Please dispose off the batteries responsibly.

Receiver unit

The receiver unit receives the Z-Wave radio signals from the 
room  thermostat.  In  the  unlikely  event  of  a  communication 
failure it is possible to override the system and switch On and 
Off using the On/Off buttons on the receiver as a local override. 

If  the  override  is  used  to  override  the  thermostat  when  it  is 
functioning correctly then the override will be cancelled by the 
next  switching  operation  of  the  thermostat  and  normal 
operation  will  be  resumed.  In  any  case,  with  no  further 
intervention, normal operation will be restored within one hour 
of the override being operated.

4

Batteries should be
changed immediately

Low battery symbol 
appears first when the
batteries are nearing the 
end of their life

Содержание RT322













Отзывы: