manualshive.com logo in svg

IQ Gate Systems IntelliSlide X6, Инструкция по установке и эксплуатации

Поделиться
Скачать
IQ Gate Systems IntelliSlide X6 Скачать руководство пользователя страница 13

 DO NOT REVERSE BATTERY POLARITY AT THE 

BATTERY OR THE CIRCUIT BOARD.  SEVERE DAMAGE WILL 
OCCUR 

The IntelliSlide X6 is a 24 volt DC gate operator.  Utilizing (2) 12 vdc batteries, 
the batteries must be connected in series, and then the positive (+) power 
wire (RED) is to be connected to the positive (+) battery terminal 

•

Take note of the software version on the LCD display upon power up. 

Chain Attachment and Limit Settings 

Using the supplied chain brackets, mount the 
brackets with the chain bolt holes at the same height 
as the bottom of the idlers. Roughly 9-10 inches from 
the base of the operator. 

Once the chain is attached, it needs to be tightened.  
Be careful not to over tighten the chain.  Proper 
adjustment is 1-2” of sag for every 10’ feet of chain. 

After the chain has been installed, the magnetic limits need to be installed.  To do so, switch the 
MOTOR SWITCH to the MANUAL position.  Push the gate in the open direction until the gate 
reaches the full open limit.  Attach the Magnetic Limit Block to the chain so that it is flush with the 
edge of the operator frame on the road side opening.  Then, push the gate closed to the desired 
closed position.  Attach the Magnetic Limit Block to the edge of the operator frame on the opposite 
edge of the operator frame. 

Be sure to install positive stops at each end of the gate.  The positive stops should be no more 
then 2 inches beyond the limit travel 

 

13

Содержание IntelliSlide X6































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды