manualshive.com logo in svg

IPS Controllers M720, Руководство пользователя

Поделиться
Скачать
IPS Controllers M720 Скачать руководство пользователя страница 22

ii.  Press and hold Mode button and then press Set Level 

button (red ORP alert LED will come on) release both 

buttons. You are now in Set Alerts mode.

iii. Press Set Level button again to display current High 

Alert

iv.  Use Up/Down button to increase/decrease ORP High 

Alert

v.  When finished, press Mode button to continue

e.  Low Alert

1.  Default: 100 mV
2.  Selectable range: OFF, 100 mV to 640 mV. A low alert 

will occur if the ORP level remains below the Low Alert 

level for 10 continuous minutes, and will automatically 

turn off the Low Alert when the ORP level rises above 

the low alert level for 1 continuous minute. During Low 

Alert, the ORP1 dose output will be disabled.

3.  Changing Low Alert setting

i.   Press Mode button to enter ORP standby
ii.  Press and hold Mode button and then press Set Level 

button (red ORP alert LED will come on) release both 

buttons. You are now in Set Alerts mode.

iii. Press Dose Time button to display current Low Alert
iv.  Use Up/Down button to increase/decrease ORP Low 

Alert

v.  When finished, press Mode button to continue

f.  pH Cal disabled

5.   Flow

a.  The controller and flow cell are shipped pre-mounted to a 

small (16” x 12”) or large (24” x 19”) ABS plastic board. The 

integrated flow switch is pre-wired to the controller.

21

M720 pH/ORP Controller Owner’s Manual

Содержание M720































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды