BMA_77024-180-11_s4 DC_en_Rev1
IPAS GmbH, Hölscherstraße 27, D-47167 Duisburg
Operating- and mounting instructions
PowerBlock s4 DC
Order number: 77024-180-11
General usage
Power Block series consists of different devices types for switching of
power and shutter control. The PowerBlock s4 DC comes in a 4 unit
DIN rail housing and can be installed in a standard distribution board.
A brief overview of the functionality is given in the following table:
Shutter channel outputs with objects for:
•
Facade control
•
True height positioning for shutter/blind
•
Shutter slits control
•
Central Up/Down functions
•
Lmits, scenes, presets, alarms, disable function, manual
control etc.
Advanced objects and functions such as:
•
Timers (with cyclic sending of time remaining)
•
Logic functions (Boolean, gate and filter functions,
comparators, math.), data point conversion
•
KNX scenes (with delays between events)
•
Setpoints
•
Analogue and digital alarms
•
Overwrite end-user parametersrr
•
Etc.
Scope of delivery
The following individual components are included in the delivery of the
PowerBlock device:
-
Complete device with inserted bus connector
-
Operating and mounting instructions
-
1x heat shrinkable tubing 1.2 x 2cm for additional insulation
of the bus cable
-
Delivered in break-proof individual packaging
Application programs
The following application programs are currently available for the
PowerBlock device:
-
77024-PowerBlock s4 DC-11-0110
Installation device
Risk of death by electric shock.
•
The device is intended for interior installation in dry rooms.
•
The device must only be installed and commissioned by an
accredited electrical engineer.
•
When planning and construction of electrical installations, the
national guidelines, rules and regulations of the country in quest-
ions are to be obeyed, as well as all current KNX guide lines.
•
For the installation the device must be switched to zero potential.
•
The device must not be opened.
•
Any faulty device is to be sent together with a return delivery to
the manufacturer.
Technical data
POWER AND OUTPUTS SPECIFICATIONS
Power supply
Supply Voltage:
Max. Consumption:
Additional power
supply:
21..30VDC
9,4mA
No
Number of outputs
Total outputs
4 outputs for DC
shutter control
with separated
supply inputs
Rated Operational
Voltage
Shutter
24V DC
Rated Current
Per Channel
6A
Load Type
Motor 24V DC
Output life
expectance
Mechanical:
Electrical:
> 5𝑥10
6
operations (at 180
times/min)
> 1𝑥10
5
cycles
with 10A load
Connections
KNX bus connection
terminal:
Terminal screw block:
Tightening torque for
terminal screw:
0,8 mm Ø solid
max. 6 mm Ø solid
maximum 0.6 Nm
GENERAL SPECIFICATIONS
Control and display
elements
Programming button:
LED, red:
8 x buttons: (for
manual channels
control)
8 x LEDs, red:
To assign the
physical address
Displays
addressing mode
To Move Up/Down
To display actual
outputs/channels
status
Mechanical data
REG casing 4TE:
Width:
Hight:
Lenght:
Weight
Mounting:
Plastic ABS
– V0
72 mm
58 mm
90 mm
235 g
35 mm DIN rail
Electrical safety
Pollution class:
Protection type:*
Protection class:**
Overvoltage category:
KNX Bus:
2
IP20
III
III
SELV DC 30V
EMC requirements
Complies with:
EMC directive
2014/30/EU
Environmental
conditions
Weather resistance:
Environmental con-
ditions in operation:
Storage emperature:
Transportation
temperature:
Rel. humidity:
(non condensing)
EN 50090-2-2
-5°C to +45°C
-25°C to +55°C
-25°C to +70°C
5 % to 93 %
Certification CE-
Signage
KNX registered:
According to EMC-
Guidelines:
Yes
(Residential and
commercial
buildings), Low
Voltage guidelines
* (according to EN 60529); ** (according to IEC 1140)
