INVT GD300-01A-011G-4 Скачать руководство пользователя страница 2

Страница: 2 / 97

Goodrive300-01A series VFD for air compressor

Preface

-i-

Preface

The Goodrive300-01A series variable-frequency drive (VFD) for air compressors (hereinafter referred

to as Goodrive300-01A VFD) is designed and optimized based on Goodrive300-01 to be applied in

synchronous/asynchronous air compressor for optimal control performance.

The Goodrive300-01A VFD carries air compressor-specific control logic to connect to various signals

of the air compressor directly eg emergency-stop, pressure and temperature signals, fan transformer

and fault signals. It can realize control over solenoid valve and provide 24V power to HMI. It also

carries Modbus communication interface to fit the HMI without external controller or PLC, simplifying

the electrical design while realizing excellent frequency-conversion control.

Goodrive300-01A VFD has undergone compatibility test with multiple mainstream motor or master

manufacturers based on the application features and actual needs of air compressor industry. It

adopts dedicated PID and unique flux-weakening design to enable the air compressor to start quickly

and run smoothly with max driving frequency reaching 400Hz and above. Through high-power

density design and compact structure, it simplifies commissioning procedures and downgrades

product size. It adopts independent air duct, heavy-load and high power factor design to cope with

challenging field and grid environment.

The Goodrive300-01A VFD in the range of 7.5

–15kW supports built-in contactor units, low-frequency

transformer and low-frequency fan. It can provide 220V/110V power to supply the solenoid valve

(hereinafter referred to as Goodrive300-01A single VFD integrated machine) and act as the extended

application of the small power of Goodrive300-21 dual VFD integrated machine, thus satisfying

diversified application needs of integrated machine.

Read this manual carefully before installation to ensure Goodrive300-01A VFD can be installed and

operated correctly to give full play to its excellent performance.

If the product is ultimately used for military affairs or manufacture of weapon, it will be listed on the

export control formulated by the

Foreign Trade Law of the People's Republic of China

. Rigorous

review and necessary export formalities are needed when exported.

Our company reserves the right to update the information of our products.

Содержание GD300-01A-011G-4


































































































Результаты поиска

Содержание GD300-01A-011G-4

Отзывы:

Похожие инструкции для GD300-01A-011G-4

Бренды по названию

Популярные бренды

INVT GD300-01A-011G-4, Руководство по эксплуатации

Результаты поиска

Содержание GD300-01A-011G-4

Отзывы:

Похожие инструкции для GD300-01A-011G-4

Бренды по названию

Популярные бренды