Invisia INV-TB16, Руководство пользователя

Страница: 10 / 14

English
OVERVIEW
Thank you for choosing the Invisia Towel Bar. Please read and understand
the instructions in this manual; keep manual for future reference. It is your
responsibility to see that your Invisia Towel Bar is properly assembled,
installed, and cared for. Failure to follow instructions in this manual could
result in serious injury or death. If you are not equipped to undertake the
outlined work, we would recommend that you have your Invisia Towel Bar
installed by a qualified contractor.
The Invisia Towel Bar is a combination grab bar and towel bar, designed to
disguise safety in a bathroom accessory. The Invisia Towel Bar is intended
for moderate vertical and horizontal load bearing to provide sitting and
standing support for people with reduced mobility. The Invisia Towel Bar is
installed with appropriate fasteners to a structural wall. The towel rung
(which holds a towel) is NOT intended to be a support product. The
maximum user weight for this product is 500lbs / 227kgs. Note: Product is
not intended to support full body weight. The Invisia Towel Bar is not to be
used in any other way than described above.
LIMITED LIFETIME WARRANTY
Products are covered by a limited lifetime warranty against defects in
materials and workmanship for the original purchaser. Warranty excludes
products that have been damaged through misuse, accidental damage,
alteration, normal wear and tear, wood material and stain, or the use of
corrosive or abrasive cleaning products.
Buyer hereby indemnifies, agrees to hold harmless and defend HealthCraft
Products Inc. from and against any and all liabilities, claims, (founded and
unfounded), losses, damages, costs and expenses (including without
limitation consequential damages and reasonable professional fees)
resulting from buyers specification, application, or improper use of goods
described hereon; buyers omission or neglect. HealthCraft Products Inc.
does not assume any liability for damage resulting from services performed
by others or faulty installation, misuse or misapplication of goods sold by
HealthCraft Products Inc. HealthCraft Products Inc. shall not be liable for
prospective profits or special, indirect, or consequential damages, or for the
cost of any corrective work done without HealthCraft Products Inc. prior
approval. HealthCraft Products Inc. total liability hereunder shall in no
event exceed the purchase price of the goods specified hereon.
Specifications subject to change without notice.
HealthCraft Products Inc.
2790 Fenton Road
Ottawa, Canada
K1T 3T7
EC REP
DELIVERY CONTENTS / TOWEL BAR FIGURE A.
1. Towel Bar
2. Wall Stem Assembly (x3)
3. #10-32 Set Screw (x3)
4. Center Punch
INSTALLATION WARNINGS FIGURE B.
1. Rail must be installed to walls that are structurally sound.
2. If desired installation location does not have adequate structure, add
wood blocking.
3. CAUTION - Do not install if there is no structure for center point.
4. CAUTION - Do not install if there is no structure for side points.
5. CAUTION - Do not install if there is no structure for outer points.
6. CAUTION - Do not install if there is no structure behind walls.
7. CAUTION - Do not install if structure behind walls is unknown.
8. CAUTION - Do not install into metal studs.
9. CAUTION - Do not install in fiberglass / acrylic shower enclosures with
insufficient stiffness and strength.
10. CAUTION - Rail and bathtub are slippery when wet.
SUGGESTED TOWEL BAR LOCATIONS FIGURE C.
To determine the optimal mounting location, we recomment holding the rail
in place and walking through the motions of a transfer (sitting, standing,
reaching ,etc.). Recommended rail height 36-48" / 914-1219mm.
INSTALLATION FIGURE D.
1. Back off set screws from rail sockets.
2. Allow wall stems to freely move in and out of rail sockets.
3. Peel off label on back of wall stems to expose sticker.
4. With wall stems inside rail sockets, push the rail against the wall.
Ensure level.
5. Firmly press the rail so stickers on back of wall stems contact wall.
6. Remove rail carefully so wall stems stay on the wall.
7. Using wall stems as locating guides, mark the tile with center punch.
8. Drill pilot holes for fasteners.
9. Fasten the wall stems to the wall using appropriate fasteners and
waterproofing.
10. Place rail back onto the fastened wall stems.
11. Secure rail to wall stems by tightening set screws. Inspect hardware
regularly, and tighten if required.
TECHNICAL DATA
See Figure E.
PRODUCT USAGE
See Figure F.
Gate 88
Kanalgatan 45B
Skellefteå, Sweden
93123
5. Lock Washer, S/S (x3)
6. 3/32" Hex Key
7. #10 x 3" Wood Screw, S/S (x3)
10