Invacare TDX-SP N Скачать руководство пользователя

Страница: 56 / 88

SECTION 8—BASE FRAME

TDX® SP

Part No 1143209

Adjusting Seat Angle (Non TRRO Wheelchairs Only)

WARNING

Wheelchairs with TRRO Only - Adjusting the back angle from the factory setting will void TRRO

compliance. After adjusting the back angle, DO NOT transport an occupied wheelchair in a

motor vehicle of any kind. The wheelchair may only be transported in a motor vehicle while

unoccupied, and will be considered TRBKTS.

TDX SP with Adult Seat

NOTE: For this procedure, refer to FIGURE 8.2.
NOTE: The following tools are required to perform this procedure.
•

5/16-inch Socket with Ratchet

•

Torque Wrench

•

Pitch Angle Gauge

Loosen but DO NOT remove the eight 5/16-18 X .75 hex head screws securing the seat-to-floor bracket to the base frame.

Using the pitch angle gauge, reposition the two seat-to-floor brackets to the desired angle.

Tighten the eight 5/16-18 X .75 hex head screws. Torque to 13 ft-lbs ± 20%.

FIGURE 8.2

Adjusting Seat Angle (Non TRRO Wheelchairs Only)

5/16-18 X .75-inch Hex

Head Screws

Base Frame

Seat-to-Floor

Bracket

Содержание TDX-SP N

























































































Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды

Invacare TDX-SP N, Руководство по обслуживанию

Результаты поиска

Содержание TDX-SP N

Отзывы:

Похожие инструкции для TDX-SP N

Бренды по названию

Популярные бренды