background image

8

ADJUSTING THE CONTOUR U SEATING SYSTEM BACK ANGLE

(FIGURE 6)

NOTE: Before performing this procedure all four (4) J brackets must be adjusted to the same depth.
Refer to ADJUSTING THE CONTOUR U SEATING SYSTEM BACK DEPTH in this instruction
sheet.

NOTE: The back to seat angle is adjusted by repositioning the top and/or the bottom J brackets.

NOTE: Adjustments made to J bracket(s) on one side of the ContourU back MUST be also be made
to the remaining J bracket(s) on the opposite side of the ContourU back.

1. If necessary, install the ContourU back. Refer to REMOVING/INSTALLING THE CON-

TOUR U SEATING SYSTEM BACK in this instruction sheet.

2. With the ContourU back installed on the wheelchair, determine which J bracket mounting

positions are necessary to achieve the desired back angle adjustment.

3. Remove the ContourU back. Refer to REMOVING/INSTALLING THE CONTOUR U

SEATING SYSTEM BACK in this instruction sheet.

4. Remove the two (2) mounting screws and locknuts that secure the J bracket to the L

bracket as shown in DETAIL “A” of FIGURE 6.

5. Align two (2) mounting holes of the J bracket with two (2) mounting holes of the L bracket

to acquire the desired angle.

6. Reinstall the two (2) mounting screws and locknuts that secure the J bracket to the L

bracket. Securely tighten.

7. Repeat STEPS 4-6 to adjust the remaining J and L brackets as necessary to achieve the

desired back angle.

8. Reinstall the ContourU back onto the wheelchair. Refer to REMOVING/INSTALLING THE

CONTOUR U SEATING SYSTEM BACK in this instruction sheet.

9. Ensure the ContourU back is set to the desired angle and does not interfere. If necessary

repeat STEPS 1-7 until desired depth is achieved.

FIGURE 6 - ADJUSTING THE CONTOUR U SEATING SYSTEM BACK

ANGLE

Upper J Brackets

ContourU Back

Locknuts

Mounting

Screws

J Bracket

Mounting Holes

L Bracket

DETAIL "A"

Lower J Brackets

Содержание OCMK01

















Отзывы: