Invacare Formula CG Elevate Скачать руководство пользователя страница 76

Страница: 76 / 95

Invacare® Formula™ CG Seating

Pull the actuator lead and magnetic switch lead from under the
rear battery handle.

Using the battery handle, lift the rear battery

up and tilt away

from the battery box

then pull to remove the rear battery

from the wheelchair.

From the front of the wheelchair, firmly grasp the front battery
strap

and pull the front battery

forward until the front

battery handle can be grasped.

10. Using the battery handle, lift the front battery up and away from

the wheelchair.

11. If replacing the batteries, remove the front and rear battery

wiring harness. Refer to 7.35 Connecting/Disconnecting Battery
Wiring Harness - TDX SP with Elevating Seat Only, page 79.

7.32.2

Installing the Batteries

If replacing the batteries, install the battery wiring harness.

If replacing the batteries, install the front and rear battery wiring
harness. Refer to 7.35 Connecting/Disconnecting Battery Wiring
Harness - TDX SP with Elevating Seat Only, page 79.

Using the battery handle and battery strap

, position the front

battery

into the battery box

Using the battery handle, position the rear battery into the
battery box.

Connect the front battery lead

from the rear battery lead

Position actuator lead and drive limit switch lead under the rear
battery handle.

Connect the following:

•

The battery wiring harness

to the controller connector

•

The drive limit switch

to the magnetic switch controller

connector

•

The elevator actuator

to the actuator controller

connector

Install the front top and rear shrouds. Refer to 7.34
Removing/Installing the Wheelchair Shrouds TDX SP, page 78

Connect the joystick. Refer to 7.26 Disconnecting/Connecting
the SPJ+ Joysticks, page 68 or 7.27 Disconnecting/Connecting
the CMPJ+ Joysticks, page 69.

Verify the joystick On/Off switch is in the On position and lower
the seat.

7.32.3

Actuator Connection Bypass Instructions

Remove the three mounting screws securing the rear shroud
to the wheelchair frame

Remove the rear shroud from the wheelchair.

1143155-R-01

Содержание Formula CG Elevate
































































































Результаты поиска

Содержание Formula CG Elevate

Отзывы:

Похожие инструкции для Formula CG Elevate

Бренды по названию

Популярные бренды

Invacare Formula CG Elevate, Руководство пользователя

Результаты поиска

Содержание Formula CG Elevate

Отзывы:

Похожие инструкции для Formula CG Elevate

Бренды по названию

Популярные бренды