Invacare Formula CG Elevate Скачать руководство пользователя страница 79

Страница: 79 / 95

Setup/Maintenance

7.34.1

Removing/Installing the Rear Shroud

Reverse this procedure to install the rear shroud.

Remove the three pan head screws

that secure the rear

shroud

to the base frame

Remove the rear shroud from the base frame.

7.34.2

Removing/Installing the Front Shroud and

Battery Retention Bracket

Reverse this procedure to install the front shroud and
battery retention bracket.

The front shroud

and battery retention bracket

are

removed from and installed onto the wheelchair frame as
a single unit.

Remove the two socket head screws

securing the front

shroud/battery retention bracket to the base frame

Lift up to unhook the battery retention bracket from the base
frame and remove the front shroud/battery retention bracket
from the base frame.

7.34.3

Removing/Installing the Top Shroud

Reverse this procedure to install the top shroud.

Remove the seat from the base frame.

Remove the four pan head screws

securing the top shroud

to the base frame

Lifting up, remove the top shroud from the base frame.

7.35

Connecting/Disconnecting Battery Wiring

Harness - TDX SP with Elevating Seat Only

FOR FRONT BATTERY

FOR REAR BATTERY

1143155-R-01

Содержание Formula CG Elevate
































































































Результаты поиска

Содержание Formula CG Elevate

Отзывы:

Похожие инструкции для Formula CG Elevate

Бренды по названию

Популярные бренды

Invacare Formula CG Elevate, Руководство пользователя

Результаты поиска

Содержание Formula CG Elevate

Отзывы:

Похожие инструкции для Formula CG Elevate

Бренды по названию

Популярные бренды