Invacare Basic Tilt Скачать руководство пользователя

Страница: 28 / 32

PROCEDURE 10

HEADREST

Depth

Adjustment

Height Adjustment

Thumb Screw

Socket Screws

FIGURE 1 - REMOVING/INSTALLING/

ADJUSTING HEADREST

Adjusting Headrest Height

1. Loosen the set screw on the headrest stop.
2. Loosen, but do not remove, the thumb screw that se-

cures the headrest to the headrest mounting bracket.

3. Position the headrest to the desired height.
4. Tighten the thumb screw that secures the headrest

to the headrest mounting bracket.

5. Tighten the set screw on the headrest stop.
6. If necessary, adjust the depth or direction of the head-

rest . Refer to ADJUSTING HEADREST DEPTH/DI-

RECTION in this procedure of the manual.

Adjusting Headrest Depth/Direction

1. Loosen, but do not remove, the three (3) socket screws

that secure the offset fixture to the slide tube.

2. If necessary, reposition the headrest to the desired

depth by sliding the headrest towards the front of the

wheelchair or towards the rear of the wheelchair.

3. If necessary, reposition the headrest to the desired

position (headrest will move in any direction). Refer to

DETAIL "A".

4. While holding the headrest in the desired position, se-

curely tighten the three (3) socket screws.

5. If necessary, adjust the height of the headrest . Refer

to ADJUSTING HEADREST HEIGHT in this proce-

dure of the manual.

REPLACING HEADREST (FIGURE 2)

1. Remove the three (3) socket screws that secure the

headrest to the headrest mounting bracket.

2. Position the new headrest on the headrest mounting

bracket and secure with the existing three (3) socket

screws.

3. If necessary, adjust the height, depth or direction of the

headrest. Refer to ADJUSTING HEADREST HEIGHT

or ADJUSTING HEADREST DEPTH/DIRECTION in

this procedure of the manual.

Headrest Stop

Set Screw

REMOVING/INSTALLING/
ADJUSTING HEADREST (FIGURE 1)

Removing

1. Loosen, but do not remove, the thumb screw that se-

cures the headrest to the headrest mounting bracket.

2. Remove the headrest from the headrest mounting

bracket.

Installing

1. Make sure thumb screw is loose.
2. Install the headrest until the headrest stop sits on the

headrest mounting bracket.

3. If necessary, adjust the height, depth or direction of the

headrest. Refer to ADJUSTING HEADREST HEIGHT

or ADJUSTING HEADREST DEPTH/DIRECTION in

this procedure of the manual.

This Procedure Includes the Following:
Removing/Installing/Adjusting Headrest
Replacing Headrest

Offset Fixture

Socket

Screws

Headrest Mounting Bracket

Headrest

NOTE: One (1) style of headrest shown for clarity.

Both styles of headrest attach the same way.

FIGURE 2 - REPLACING HEADREST

Left to Right

Adjustment

Side to Side

Adjustment

Up and Down

Adjustment

Slide Tube

DETAIL "A"

WARNING

After ANY adjustments, repair or service
and BEFORE use, make sure all attaching
hardware is tightened securely - other-
wise injury or damage may result.

Headrest Mounting Bracket

Содержание Basic Tilt

































Результаты поиска

Содержание Basic Tilt

Отзывы:

Похожие инструкции для Basic Tilt

Бренды по названию

Популярные бренды

Invacare Basic Tilt, Руководство пользователя

Результаты поиска

Содержание Basic Tilt

Отзывы:

Похожие инструкции для Basic Tilt

Бренды по названию

Популярные бренды