background image

28

Appendix A

Digital’s SRM Console Settings

When the ITI-5232E is being used in a Digital Alpha platform running OpenVMS or
Digital UNIX, the SRM console is  used to set the port speed, media (cable) type and boot
protocols, and can also be used to test the module.

After powering your system up, and before booting your operating system, the system
will stop at the SRM console prompt.  On a uni-processor machine, the SRM prompt is
“>>>” and on the primary processor of a multi-processor machine, is “P0>>>”.

Digital uses a set of “Environment Variables” to store the settings of certain user
definable parameters, which are passed to the operating system to allow the users
configuration information to stay consistent when the SRM passes control of the system
to the operating system.

Displaying and Setting Ethernet Port Characteristics

The Alpha console recognizes the Ethernet device as an EW port.  There are two
commands that are necessary for setting and showing the Ethernet port:

SET and SHOW.

Use SHOW to display characteristics of the Ethernet port.

>>>Show EWn0_MODE

Where ‘n’ is the Ethernet port letter.

Use SET to set characteristics of the Ethernet port.  The available settings for
Ethernet media type are shown in Table 4.

Parameter

Settings

Description

EWn0_MODE

TWISTED-PAIR

10Mb/sec Twisted Pair

FAST

100Mb/sec Twisted Pair
Half Duplex

FULL DUPLEX TWISTED PAIR

Full Duplex Twisted Pair

AUI

Not Supported

BNC

Not Supported

FAST FD

FAST Full Duplex

Table 4 Digital UNIX and OpenVMS SRM Console Media Selection

Содержание ITIpci 5232E





































Отзывы: