Intex SF60110-1 Скачать руководство пользователя страница 14

195

PO

SAVE THESE INSTRUCTIONS

(195PO)  SAND FILTER PUMP  ENGLISH  7.5” X 10.3”  PANTONE 295U  06/29/2016

English

Page 14

OPERATING INSTRUCTIONS

Valve Position

Function

Water Flow Direction

FILTER

(see drawing 23)

 Normal filtration and regular 
 vacuuming of pool

  From pump through filter media       
  to pool

BACKWASH

(see drawing 24)

 Reverses water flow to clean         
 filter media

  From pump through filter media   
  to valve waste/drain outlet

RINSE

(see drawing 25)

  For initial startup cleaning of the sand, and  
 leveling the sand bed after backwashing

  From pump through filter media to 
  valve waste/drain outlet

WASTE

(see drawing 26)

 For vacuuming directly to waste, 
 lowering pool level or to drain the pool

  From pump to valve waste/drain    
  outlet bypassing the filter media

RECIRCULATE

(see drawing 27)

 For circulating water back to pool 
 without going through the filter media

  From pump through valve to    
  pool bypassing the filter media

CLOSED

(see drawing 28)

  Shuts off all flow to filter and pool
 

“Do not use this setting with pump running”

6-way valve positions and function:

  •  Risk of electric shock. Connect this product only to a grounding type receptacle 
    protected by a ground-fault circuit interrupter (GFCI) or residual current device 
    (RCD). Contact a qualified electrician if you cannot verify that the receptacle is 
    protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, 
    which has a maximum rate of 30 mA. Do not use a portable residual current 
   device (PRCD).
 

  To reduce the risk of electric shock, do not use extension cords, timers, plug 

    adaptors or converter plugs to connect unit to electric supply; provide a 
    properly located outlet.

  •

  Do not attempt to plug in or unplug this product while standing in water or when 

    your hands are wet.
  •  Never operate this product above the maximum working pressure stated on the 
   filter tank.
  •  Always switch off pump before changing the 6-way valve position.
  •  Operating this product without water flowing through the system can cause a 
    build up of hazardous pressure which can result in an explosive situation, serious 
    injury, property damage or death.
  •  Never test this pump with compressed air. Never operate the system with water 
    temperature above 35°C (95°F).

WARNING

R E T L I

F

E S N

I R

ET

AL

U

C

RI

C

E

R

E

S

O

L

C

ET

S

A

W

B

23

E S N

I R

ET

AL

U

C

RI

C

E

R

H

S

A

W

K

C

A

B

E

S

O

L

C

ET

S

A

W

24

R E T L I

F

E S N

I R

ET

AL

U

C

RI

C

E

R

H

S

A

W

K

C

A

B

ET

S

A

W

25

Содержание SF60110-1

























Отзывы: