background image

250

A

S  AVE THESE INSTRUCTIONS

(250IO)  SPA (JET + HARD WATER)  ENGLISH  7.5” X 10.3”  PANTONE 295U  12/12/2014

English

TROUBLESHOOTING

Page 20

PROBLEM

CAUSE

SOLUTION

NO DISPLAY/SPA 
CONTROL UNIT DOES 
NOT WORK

•  Spa is unplugged or off.
•  Control panel cable plug loose.
• Power failure.
• RCD tripped.
• RCD broken.

•  Ensure the spa is plugged and switched on.
•  Ensure the control panel cable plug is 

fi

 rmly attached 

  to the control base receptacle.
•  Check power source.
•  Reset the RCD.
•  Contact Intex Service Center.

HOUSEHOLD CIRCUIT 
BREAKER TRIPPED

•  Circuit breaker under rated.
•  Overloaded circuit breaker.
•  An electrical fault in the line.

•  Ensure correct circuit breaker rating.
•  Provide a dedicated circuit breaker feeding the spa 
  electrical outlet only.
•  Contact a qualify electrician to correct the electrical fault.

NOT HEATING
PROPERLY

•  Temperature set too low.
• Dirty 

fi

 lter cartridge.

•   Water temperature decreasing during  
  heater STANDBY mode.
•  Heating element failed.

•  Increase the temperature and attach the spa cover.
•  Clean or replace the 

fi

 lter cartridge in time.

•  If heater is in STANDBY mode, press the 

fl

 ame button 

    twice to heat up the water to the set temperature.
•  Contact Intex Service Center.

JET FUNCTION DOES
NOT WORK

•  Jet pump is too hot.

•  Turn off and unplug the spa. Let it cool down and  
  restart all over again.
•  If problem persists contact Intex Service Center.

JET OUTPUT IS WEAK

•  Low water level.
•  Obstruction in the suction inlet inside the tub.
•  Jet nozzles clogged or dirty.
•  Jet nozzles plumbing pipes damaged.

•  Add water between MIN and MAX level.
•  Ensure suction inlet is not covered or blocked.
•  Clean any dirt inside the jet nozzles.
•  Contact Intex Service Center.

JET AIR CONTROL 
KNOB NOT WORKING

•  Jet nozzles clogged or dirty.
•  Control panel jet air

fl

 ow hose loose or damaged.

• Jet air

fl

 ow plumbing inside the spa tub 

  damaged.

•  Clean any dirt inside the jet nozzles.
•  Ensure the jet air hose in the control panel is not 
  damaged and securely attached. Replace if needed.
•  Contact Intex Service Center.

FILTRATION PUMP 
NOT WORKING

• Dirty 

fi

 lter cartridge.

•  Filtration inlet and/or outlet clogged.
•  Filter pump motor failed.

•  Clean or replace the 

fi

 lter cartridge in time.

•  Check and clean 

fi

 ltration inlet and outlet regularly.

•  Contact Intex Service Center.

WATER NOT CLEAN

•  Cartridge assembly not properly attached. 
• Insuf

fi

 cient 

fi

 ltering time.

• Dirty 

fi

 lter cartridge.

•  Improper water maintenance.
•  Filtration inlet and outlet clogged.

•  Ensure the cartridge assembly is properly attached.
• Increase 

fi

 ltration time.

•  Clean or replace the 

fi

 lter cartridge in time.

•  Keep the spa water properly sanitized. Refer to the 
  chemical manufacturer’s instructions.
•  Check and clean 

fi

 ltration inlet and outlet regularly.

PUMP CONNECTORS 
ARE NOT LEVEL WITH 
THE SPA CONNECTORS

•  One characteristic of PVC is that 
  it changes shape, which is normal.

•  Elevate the pump with wood or another type of  
  insulated material to bring the pump’s connectors  
  level with the spa’s connectors.

TUB HAS A STRANGE 
SHAPE

•  Expanded internal air pressure by 
 strong 

sunshine.

•  Do not expose the product under direct sunshine.
•  Check the air pressure and release air if necessary. 
  During very hot weather, you must check to see 
  whether it is necessary to release some air. This is to 
  avoid any possible damage to the tub.

TUB LOSES AIR 
PRESSURE

•  Air valve cap loose.
•  Air valve base loose.
•  Hole, cut or split on spa tub.

•  Ensure air valve cap is securely closed.
•  Fill up the spa tub with air then make sure the air valve 
  base is tighten, see “Spa Tub Air Valve Fastening” section.
•   Put liquid soap and water in a squirt bottle and spray 
  on seams. If there is a leak it will bubble. After you 

fi

 nd 

  the leak, clean and dry the leaking area, then apply the 
  repair patch that comes with your spa.

LEAKING BETWEEN 
SPA TUB CONNECTORS 
AND CONTROL UNIT 
CONNECTORS

•   Spa control base inlet/outlet connections  
  not securely tight.
•   Spa control base inlet/outlet o-ring 
 missing/dirty.

•   Tighten inlet and outlet connections.
•   Coat the o-ring with petroleum jelly for water proof.

SPA IS TOO NOISY 
IN FILTRATION MODE 
ONLY

•   Control base components not securely  
 attached.
•  Control base ground not level and 

fi

 rm.

• Spa 

fi

 lter motor failed.

•  Ensure control panel, back cover and all inlet/outlet  
  are securely connected.
•  Ensure ground is level, 

fi

 rm and smooth.

•  Replace the failed 

fi

 lter motor with a new one.

Содержание PureSpa SPJ-H-20-1






















Отзывы: