background image

119A

SAVE THESE INSTRUCTIONS

(119IO)  RECTANGULAR ULTRA FRAME POOL  ENGLISH  7.5” X 10.3”  PANTONE 295U  07/17/2013

English

Page 9

POOL SETUP (continued)

9. 

Position the long wall top rails so they are leaning over the 

 

short wall top rails. Installe the corner joints 

(8)

 at the 4 

 

corners (see drawing 9).

 

IMPORTANT: The four corner joints are designed to be

 

moveable relative to the horizontal beams and not fixed 

 

to the horizontal beams. This allows the pool side walls 

 

to move inward or outward when the pool is in use.

10. 

Assemble the ladder. The ladder has separate assembly instructions in the ladder box. 

11. 

Place the assembled ladder over one of the sides with one of the liner installation team members 

 

entering the pool to smooth out all bottom liner wrinkles. While inside the pool this team member 

 

should check the 2 drain valves (in corners) to be sure the inside drain plug is inserted into the valve. 

 

This team member should push inside corner in an outward direction.

 

12. 

Before filling the pool with water, ensure that the drain plug inside the pool is closed and that the drain 

 

cap on the outside is screwed on tightly. Fill the pool with no more than 1 inch (2.5 cm) of water. Check 

 

to see whether the water is level.

 

 

IMPORTANT: If the water in the pool flows to one side, the pool is not completely level. Setting 

 

up the pool on unleveled ground will cause the pool to tilt resulting in the sidewall material to 

 

bulge. If the pool is not completely level, you must drain the pool, level the area and re-fill the 

 pool.

 

 

 

Smooth out the remaining wrinkles (from inside the pool) by pushing out where the pool floor and pool 

 

sides meet. Or, (from outside pool) reach under the side of the pool, grasp the pool floor and pull it out. 

 

If the ground cloth is causing the wrinkles, have 2 people pull from either side to remove all wrinkles.

13.  

Fill the pool with water up to just below the sleeve line. (see 

 

drawing 10).

 

NOTE:

 The pool side walls and frame structure will lean    

 

inward after having been filled with water to the 

 

recommended level. Do not be concerned by the inward 

 

leaning of the side walls, this is to accommodate the water 

 

movement and pressure when the pool is in use.

9

8

IMPORTANT

Before allowing anyone to use the pool, hold a family meeting. Establish a set of rules that 

include, at a minimum, the important safety rules and general aquatic safety  information in 

this manual. Review these rules on a regular basis and with all users of the pool, including 

guests.

 

WATER LEVEL

10

Содержание Rectangular Ultra Frame Pool













Отзывы: