background image

  

MH-RC-MBS-1

 

User’s Manual r6.

3 EN

 

 

 

 

© Intesis Software S.L.U. - All rights reserved 

This information is subject to change without notice

 

 

IntesisBox

®

 

is a registered trademark of Intesis Software SLU

 

 

URL 
Email
Phone 

 

http://www.intesisbox.com                                          
info@intesisbox.com 
+34 938047134 

 22/23 

 

7.

 

Error Codes 

 

Error Code 

Modbus

 

Error in 

Remote 

Controller 

Error Description 

N/A 

No active error 

1  

E1 

Remote controller communication error 

E2 

Duplicated indoor unit address 

3  

E3 

Outdoor unit signal line error 

5  

E5 

Communication error during operation 

E6 

Indoor heat exchanger temperature thermistor anomaly  

E7 

Indoor return air temperature thermistor anomaly 

E8 

Heating overload operation 

E9 

Drain trouble  

10 

E10 

Excessive number of indoor units (more than 17) by controlling one 

remote controller 

12 

E12 

Address setting error by mixed setting method 

14 

E14 

Communication error between master and slave indoor units 

16 

E16 

Indoor fan motor anomaly 

19 

E19 

Indoor unit operation check, drain motor check setting error 

28 

E28 

Remote controller temperature thermistor anomaly 

30 

E30 

Unmatched connection of indoor and outdoor unit 

31 

E31 

Duplicated outdoor unit address No. 

32 

E32 

Open L3 Phase on power supply at primary side 

33 

E33 

Inverter primary current error 

35  

E35 

Cooling overload operation 

36 

E36 

Discharge pipe temperature error 

37 

E37 

Outdoor heat exchanger temperature thermistor anomaly 

38 

E38 

Outdoor/Ambient air temperature thermistor anomaly 

39 

E39 

Discharge pipe temperature thermistor anomaly 

40  

E40 

High pressure error 

41 

E41 

Power transistor overheat 

42 

E42 

Current cut 

43  

E43 

Excessive number of indoor units connected, excessive total capacity of 

connection 

45 

E45 

Communication error between inverter PCB and outdoor control PCB 

46 

E46 

Mixed address setting methods coexistent in same network 

47 

E47 

Inverter over-current error 

48 

E48 

Outdoor DC fan motor anomaly 

49 

E49 

Low pressure anomaly 

51 

E51 

Inverter anomaly 

53 

E53 

Suction pipe temperature thermistor anomaly 

54 

E54 

High/Low pressure sensor anomaly 

55 

E55 

Underneath temperature thermistor anomaly 

56 

E56 

Power transistor temperature thermistor anomaly 

57 

E57 

Insufficient in refrigerant amount or detection of service valve closure 

58 

E58 

Anomalous compressor by loss of synchronism 

59 

E59 

Compressor startup failure 

60 

E60 

Rotor position detection failure / Anomalous compressor rotor lock 

61 

E61 

Communication error between the master unit and slave units 

63  

E63 

Emergency stop 

65532 

(-4) 

N/A 

Initialization process (around 2min) before normal operation starts. This 

error appears in case that MH-RC-MBS-1 is set as Master. 

65535  

(-1) 

N/A 

Communication error of MH-RC-MBS-1 or Remote controller with the AC 

unit. 

 

Содержание MH-RC-MBS-1
























Отзывы: