IntesisBox MH-RC-MBS-1 Скачать руководство пользователя страница 20

Страница: 20 / 23

MH-RC-MBS-1

User’s Manual r6.

3 EN

This information is subject to change without notice

IntesisBox

is a registered trademark of Intesis Software SLU

URL
Email
Phone

http://www.intesisbox.com
[email protected]
+34 938047134

20/23

Mechanical and electrical features

Enclosure

Plastic, type PC (UL 94 V-0)
Net dimensions (dxwxh):
93 x 53 x 58 mm /

3.7”

x 2.1” x 2.3”

Color: Light Grey. RAL 7035

Operation
Temperature

0ºC to +60ºC

Weight

85 g.

Stock
Temperature

-20ºC to +85ºC

Mounting

Wall
DIN rail EN60715 TH35.

Operational
Humidity

<95% RH, non-condensing

Terminal Wiring
(for low-voltage
signals)

For terminal: solid wires or stranded wires
(twisted or with ferrule)

1 core: 0.5mm

… 2.5mm

2 cores: 0.5mm

… 1.5mm

3 cores: not permitted

Stock Humidity

<95% RH, non-condensing

Modbus RTU
port

1 x Serial EIA485 Plug-in screw terminal
block (2 poles):

A, B

Compatible with Modbus RTU EIA-485
networks

Isolation voltage

1500 VDC

AC unit port

1 x XY bus Plug-in screw terminal block
(2 poles):

X, Y

Compatible with Mitsubishi Heavy Industries
networks

Isolation
resistance

1000 MΩ

Switch 1
(SW1)

1 x DIP-Switch for AC features

Protection

IP20 (IEC60529)

Switch 3
(SW3)

1 x DIP-Switch for Modbus RTU settings

LED indicators

2 x Onboard LED - Operational
status

Switch 4
(SW4)

1 x DIP-Switch for extra functions

EIA-485

Port

AC Unit

connection

DIP

Switch SW1

DIP

Switch SW3

LED

Indicators

DIP

Switch SW4

Содержание MH-RC-MBS-1
























Результаты поиска

Содержание MH-RC-MBS-1

Отзывы:

Похожие инструкции для MH-RC-MBS-1

Бренды по названию

Популярные бренды

IntesisBox MH-RC-MBS-1, Руководство пользователя

Результаты поиска

Содержание MH-RC-MBS-1

Отзывы:

Похожие инструкции для MH-RC-MBS-1

Бренды по названию

Популярные бренды