InterVac garage vac GH-120, Быстрый старт

Страница: 4 / 11

the GarageVac to secure in place. If the vacuum cleaner is loose, you will need to tighten the
screws further.
8. The hose retainer is right side up if you can read the word “Warning” impression correctly .
Secure the hose retainer on the front panel of the GarageVac with the two small black screws.
(There is a small indentation on the retainer where the screws can penetrate).
ALWAYS CHECK TO BE SURE THE DUST BAG AND MOTOR FILTER ARE IN PLACE BEFORE
USING!
Model GF-120 and GF-220 Recessed installation into Drywall (Gypsum Wall)
GROUNDING INSTRUCTIONS FOR GF-120 VOLT ONLY, WHEN PERMANENTLY WIRED
This appliance must be connected to a grounded metal, permanent wiring system or an equipment-
grounding conductor must be run with the circuit conductors and connected to the equipment-grounding
terminal or lead on the appliance.
WARNING: Disconnect all electrical power to the wall area before installing! Do not drill near
studs where electrical cable may be secured to studs adjacent to receptacles.
NOTE: The four mounting holes in the outer corners of the flange of the power unit must be
drilled from the back of the unit with a 3/16” (4.5mm) drill bit when the unit is to be recessed into a
wall.
For added stability, mount against the side of a wall stud.
1. Before making the cutout, ensure that no electrical switches or outlets are obstructing the area.
2. Tape template L-45 against the wall a minimum of 3” from the floor to allow for exhausting air.
3. Install 14-gauge (1.0mm) AWG, 300V minimum Romex cable (use wire cutters rated for at least
95C) from the electrical power supply and pull the power cable through the wall cut-out.
4. North American Installation: Remove the side cover plate of the vacuum and pull the three inside
wires through the opening. Insert the 120-volt power supply cable through the Romex clamp and
out through the side opening. With three wire nuts, connect black to black, white to white and
green to bare ground conductor wires. Tighten the Romex clamp and replace the side cover.
5. European installation (220/230 volt). Does not require a ground wire . The vacuum cleaner is
double insulated: Pull the two wires with the terminal block out. Connect the power cable to the
terminal block inside the housing. With a pair of pliers, insert the cable with the strain relief (CE)
and replace the side cover.
6. Slide the unit, bottom first, into the opening and secure with the four screws.
7.
The hose retainer is right side up if you can read the word “Warning” impression correctly
.
Secure the hose retainer on the front panel of the GarageVac with the two small black screws.
(There is a small indentation on the retainer where the screws can penetrate).
8. Check to be sure the dust bag and motor filter are in place.
HOW TO OPERATE YOUR GARAGEVAC
GarageVac is equipped with a thermal protector on the motor. If your vacuum shuts off due to
overheating, turn the switch to off and allow to cool. It will reset after about one hour. (See
trouble shooting guide).
A. Connecting and disconnecting the hose.
1. Lift the inlet valve cover on the front of the door.
2. Insert hose cuff with a twist and a firm push to secure.
3. To remove, turn hose in either direction while pulling hose towards you.
B. On / Off Switch
1. To start the vacuum cleaner, push the switch to the “I” position.
2. To stop the vacuum cleaner, push the switch to the “O” position
C. How to change the dust bag. (Uses Y-08 single bag and Y08-5 replacement bags).
1. Open the door on the vacuum cleaner by pushing the latch upward and remove both door
and dust bag.
2. To avoid spillage, carry door with dust bag attached to the trash container. Dispose of full
bag.