Interroll SH 1100 Скачать руководство пользователя страница 73

Страница: 73 / 88

Interroll Module belt conveyor SH 1100

Version 1.0 (06/2022) en
Translation of original operating instructions

Troubleshooting

In case of a fault

DANGER

Danger to life from electrocution

Only perform maintenance and repair work after you have switched off power.

Faults on electrical equipment may be rectified only by a trained electrician!

Immediately power down the module and ensure that it cannot be started accidentally.

Remove material and objects that block the conveyor.

Before switching it on again, ensure that no persons are at risk.

Properly dispose of any gear oil that has leaked. Have the motor replaced by qualified
personnel, if necessary.

Troubleshooting

Fault

Cause

Remedy

Conveying goods jam
between the side guides

Conveying goods sit on the
module at an angle

Align conveying goods parallel
to the side guide

Center of gravity of the load is
not centered

Align the center of gravity of the
load

Transport process cannot
be started and motor does
not run

Main switch and/or control
turned off

Check the switch position; turn
on main switch and/or key
switch of the control as required

Supply line damaged

Check supply line

Transport process cannot
be started and motor is
running

Module conveyor too loose

Retension module conveyor

Transport weight too high

Observe maximum weight

Transport shows jerky
movements

Foreign objects in roller area

Remove foreign objects

Conveying goods are not
being transported

Defective drum motor

Replace defective motor

Defective roller

Replace defective roller

Module conveyor brushes
against the side frame

Module conveyor adjustment is
not straight

Adjust module conveyor

Содержание SH 1100

























































































Результаты поиска

Содержание SH 1100

Отзывы:

Похожие инструкции для SH 1100

Бренды по названию

Популярные бренды

Interroll SH 1100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SH 1100

Отзывы:

Похожие инструкции для SH 1100

Бренды по названию

Популярные бренды