Interroll SH 1100 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 88

background image

Interroll Module belt conveyor SH 1100

Maintenance and repair

72

Version 1.0 (06/2022) en

Translation of original operating instructions

LED green

LED yellow

Meaning

On

Off

Photo cell is operational.
No signal from reflector.

On

On

Photo cell is correctly adjusted.
Light beam is well reflected.

On

Flashing

Photo cell is operational.
Weak signal.
Reflector is dirty, damaged or not correctly adjusted.

Replacing the reflector

2

1

3

Reflector

1

Reflector

3

Fastening clip

2

Sensor holder

The reflector is replaced in the same way as the photo cell:

Requirement:

R

The module is shut down.

4

Loosen the fastening clip (3) under the sensor holder (2).

4

Remove old reflector (1) from sensor holder.

4

Place new reflector at the same location. The studs of the reflector (1) are guided through
the holes in the sensor holder (2) and secured with the fastening clip (3) from the opposite
side. The clip engages noticeably through lateral movement and secures the reflector in
place.

«
...
70
71
72
73
74
...
»

Содержание SH 1100

























































































Отзывы:

Нет отзывов

Похожие инструкции для SH 1100

Бренд: T-Drill Страницы: 75

Бренд: Zeiss Страницы: 38

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: Haag-Streit Страницы: 18

Бренд: Haag-Streit Страницы: 20

Бренд: V-TEK Страницы: 2

Бренд: V-TEK Страницы: 112

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: laerdal Страницы: 8

Бренд: LAHTI PRO Страницы: 16

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 8

ActiveFinder One

Бренд: LaserLiner Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды