MODEL IQ333, IQ333EHS & IQ333D QUICK REFERENCE GUIDE
Should you require further assistance, please email
www.interquartz.com.au
STORE Key
Press STORE to store a number in the Memory. Any memory
can store 32 digits.
RECALL Key
For use with the host telephone system to invoke special
network facilities such as Call Hold or Call-Transfer available in
your system.
REDIAL/PAUSE Key
Press the key to redial the last number (max 32 digits), or direct
redial of an unsuccessful number dialed without going off line.
Pause may be required if your phone is connected to any
network where a momentary pause is needed during dialing. Lift
Handset, dial any digits required before the pause, press
PAUSE, and dial remaining digits. Pause is also storable in a
memory.
MEMORY Keys
Many different numbers and codes can be stored via 10 Direct
Access One-Touch Memory Keys.To store, lift Handset, press
STORE to store a number in the Memory. Any memory can
store 32 digits.
ELECTRONIC VOLUME CONTROL Keys
For the adjustment of the receive volume of the HANDSET,
HEADSET (wired and wireless headsets) or HANDSFREE
hearing level in 4 steps. Press the up and down arrow keys
(v- and v+) located in the centre of the memory card to adjust
the volume. Adjusting these controls does not affect your
outgoing voice level.
MUTE Key and Indicator
When pressed, it cuts off transmission from the handset,
handsfree and headset microphones to allow user privacy. The
red light indicates when the mute condition is active. To release
the mute condition press MUTE again.
HEADSET MIC ADJUST CONTROL
To adjust the headset's microphone sensitivity. The control is
located on the underside of the telephone.
HANDSFREE / HEADSET Key and Indicator
(with auto-detection)
When the HANDSFREE/HEADSET key is pressed a red
indicator will glow to indicate that the HANDSFREE mode or
HEADSET mode is activated and the unit is on line.
In IQ333EHS model, when the EHS control cable is connected
to unit, its HANDSFREE/HEADSET key function will be disabled
and controlled via the wireless headset.
HEADSET
MIC ADJUST
Figure 2 - Savi Office Connection Diagram for IQ333EHS
Figure 1 - Savi Office & Lifter Connection Diagram for IQ333 & IQ333D
HANDSFREE/
HEADSET
MUTE
REDIAL/
PAUSE
RECALL
Ringer Indicator
Flashes when the telephone rings with an incoming call.
Message Waiting Indicator
Illuminates when a message is waiting in your voicemail system
(depends on system compatibility). The built-in Message
Waiting function offers compatibility with various systems, while
other system types require optional extras to be fitted to the
IQ333 by Interquartz at time of order.
OLI & EHS Jacks
PMJ
FIT
Figure 3
Ringer Volume Switch (Hi/Low/Off)
The three available positions allow selection of OFF (no sound),
LOW volume, and HIGH volume of the telephone's ringing
sound during an incoming call.
Telephone
Network
Outlet
Plantronics Telephone
Interface Cable
Interquartz EHS Cable
IQ333EHS
Savi Office
(WO100, WO200 etc)
Interquartz
Line Cord
Interquartz Cable
Plantronics Cable
Plantronics
Base Power Supply
Mains
Power
Outlet
OLI
Set Headset Polarity Switch to "P"
Step 1
Set Configuration Switch to "A"
Step 3
HEADSET
MIC ADJUST
Step 2
Set Headset Mic Adjust Control
fully clockwise to Recommended
Setting Position as shown
Set Desk Phone Speaking Volume
to "1" and Desk Phone Listening
Volume to "3"
Step 4
Telephone
Network
Outlet
IQ333
Savi Office
(WO100, WO200, W7 Series)
Interquartz
Line Cord
Interquartz Cable
Plantronics Cable
Plantronics
Base Power Supply
Mains
Power
Outlet
OLI
Set Headset Polarity Switch to "P"
Step 1
Set Configuration Switch to "A"
Step 3
HEADSET
MIC ADJUST
Step 2
Set Headset Mic Adjust Control
fully clockwise to Recommended
Setting Position as shown
Set Desk Phone Speaking Volume
to "1" and Desk Phone Listening
Volume to "3"
Step 4
Plantronics Telephone
Interface Cable
Plantronics
Lifter Power Cord
Interquartz
Handset Cord
HL10
Lifter
