International comfort products F9MVE A3 Series Скачать руководство пользователя страница 21

Страница: 21 / 55

INSTALLATION INSTRUCTIONS

Gas Furnace: (F/G)9MVE

440 01 4401 02

Specifications subject to change without notice.

NOTE

: Bottom closure must be used when leveling legs are

used. It may be necessary to remove and reinstall bottom

closure panel to install leveling legs. To remove bottom closure

panel, see Step 1 in Bottom Return Air Inlet section.
To install leveling legs:

1. Position furnace on its back. Locate and drill a hole in

each bottom corner of furnace.

2. For each leg, install nut on bolt and then install bolt with

nut in hole. (Install flat washer if desired.)

3. Install another nut on other side of furnace base. (Install

flat washer if desired.)

4. Adjust outside nut to provide desired height, and tighten

inside nut to secure arrangement.

5. Reinstall bottom closure panel if removed.

DOWNFLOW INSTALLATION

NOTE

: The furnace must be pitched as shown in

Figure 19

for

proper condensate drainage.

Supply Air Connections

NOTE

: For downflow applications, this furnace is approved for

use on combustible flooring when any one of the following two

accessories are used (see specification sheets for list of

approved accessories):

•

Special Base

−

NAHA01101SB

•

Cased Coil Assembly

−

EAM4X, END4X, ENW4X

1. Determine application being installed from

Table 5

2. Construct hole in floor per

Table 5

and

Figure 22

3. Construct plenum to dimensions specified in

Table 5

and

Figure 22

4. Install as shown in

Figure 24

. If Coil Assembly Part is

used, install as shown in

Figure 25

Figure 22

Floor and Plenum Opening

Dimensions

A96283

NOTE

: It is recommended that the perforated supply

−

air duct

flanges be completely removed from furnace when installing

the furnace on a factory

−

supplied cased coil or coil box. To

remove the supply

−

air duct flange, use wide duct pliers or hand

seamers to bend flange back and forth until it breaks off. Be

careful of sharp edges. (See

Figure 23

)

CAUTION

CUT HAZARD

Failure to follow this caution may result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use care

and wear appropriate protective clothing, safety glasses and

gloves when handling parts, and servicing furnaces.

Connect supply

−

air duct to supply

−

air outlet on furnace. Bend

flange inward past 90

with wide duct pliers (See

Table 1

Figure 23

) The supply

−

air duct must be connected to ONLY

the furnace supply outlet or air conditioning coil casing (when

used). When installed on combustible material, supply

−

air duct

must be connected to ONLY the factory

−

approved accessory

subbase, or a factory

−

approved air conditioning coil casing.

NOT

cut main furnace casing to attach supply air duct,

humidifier, or other accessories. All supply

−

side accessories

MUST be connected to duct external to furnace casing.

Return Air Connections

WARNING

FIRE HAZARD

A failure to follow this warning could cause personal injury,

death and/or property damage.
Never connect return

−

air ducts to the back of the furnace.

Follow instructions below.

The return

−

air duct must be connected to return

−

air opening

(bottom inlet) as shown in

Figure 28

. DO NOT cut into casing

sides (left or right). Bypass humidifier connections should be

made at ductwork or coil casing sides exterior to furnace. (See

Figure 28

)

Bottom Return Air Inlet

These furnaces are shipped with bottom closure panel installed

in bottom return

−

air opening. Remove and discard this panel

when bottom return air is used. To remove bottom closure

panel, perform the following:

1. Tilt or raise furnace and remove four (4) screws holding

bottom plate. (See

Figure 20

)

2. Remove bottom plate.
3. Remove bottom closure panel.
4. Reinstall bottom plate and screws.

HORIZONTAL INSTALLATION

NOTE

: The furnace must be pitched forward as shown in

Figure 19

for proper condensate drainage.

WARNING

FIRE, EXPLOSION, AND CARBON MONOXIDE

POISONING HAZARD

Failure to follow this warning could result in personal

injury, death, or property damage.
Do not install the furnace on its back or hang furnace with

control compartment facing downward. Safety control

operation will be adversely affected. Never connect

return

−

air ducts to the back of the furnace.

Содержание F9MVE A3 Series
























































Результаты поиска

Содержание F9MVE A3 Series

Отзывы:

Похожие инструкции для F9MVE A3 Series

Бренды по названию

Популярные бренды

International comfort products F9MVE A3 Series, Руководство по установке

Результаты поиска

Содержание F9MVE A3 Series

Отзывы:

Похожие инструкции для F9MVE A3 Series

Бренды по названию

Популярные бренды