INSTALLATION PJB2175 & PJB4175
Because of our commitment to continuing research and improvements, Intermatic Incorporated reserves the right to make changes, without notice, in the specifications and material
contained herein and shall not be responsible for any damages, direct or consequential, caused by reliance on the material presented.
INTERMATIC INCORPORATED,
SPRING GROVE, IL 60081-9698
http://www.intermatic.com
158PA13021
ONE YEAR LIMITED WARRANTY
If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, except diverter seal, which is warrantied for the life
of the product Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended to the original household purchaser only
and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use;
(b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) dam-
ages exceeding the cost of the product; (e) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear;
(f) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN
THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW
LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof
of purchase, postage prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd.,
Spring Grove, Illinois 60081-9698/815-675-7000 http://www.intermatic.com Please be sure to wrap the product securely to avoid shipping damage.
TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE(S)
CORRECTIVE ACTION
1. On light is OFF
a. Burned - out bulb
a. Replace bulb
b. Bad connection
b. Correct defect
2. All lights are OFF
a. Tripped breaker
a. Reset breaker
b. Open GFCI
b. Call Electrician
A wiring layout should be prepared ahead of the
installation of this Junction Box with considera-
tions given to the following details.
1. Installation shall be according to Article
680 of the National Electric Code and all
applicable local Codes. This Junction Box
is suitable for either line or low voltage
luminaires.
2. Use copper conductors only.
3. This Junction Box will accommodate
water resistant flexible cord, #16/3 or
#14/3 Extra-hard usage (Type SOW, STW
or STOW) or, #12/3 or #10/2 Hard usage
(Type SJW, SJTW or SJTWO).
4. The Junction box must be rigidly
supported and unused conduit openings
permanently plugged with the plugs
provided.
Installation
1. Determine best location for the Junction Box and run
properly sized conduits as per the wiring layout.
The
Junction Box shall be located not less than 4 feet
from the inside wall of the pool. It must also be at
least 8 inches above the maximum water level and
not less than 4 inches above deck or grade.
(See
Illustration) Make sure the Junction Box can be rig-
idly supported. The optional mounting bracket (Model
PA114) is designed to accommodate either wall or
stake mounting.
2. Cut off all conduits at the same level. Use reducer
bushings furnished as needed for installation. For 1/2
inch conduit, apply PVC Solvent Cement 1 inch down
conduit and to small inside diameter of reducer bushing.
Slide small end of reducer bushing over conduit to the
stop tab. For 3/4 inch conduit, break the stop tab off of
reducer bushing and PVC Solvent Cement large inside
diameter of reducer bushing to conduit. PVC Solvent
Cement large outside diameter of reducer bushings or 1
inch conduit to Junction Box base.
Permanently close
all unused conduit openings with the plugs provided.
3. An optional external bonding lug is provided. Connect to
Equipotential Bonding Grid, if your installation requires it.
4. Pull supply conductors from source and flexible cord
from luminaires into Junction Box. Use twist on wire
connectors or other approved termination method for
power connections. Connect ground conductors and
bonding conductors, if required, to ground bar. Tighten
terminal screws 35 in-lbs minimum.
5. Install strain reliefs. The direction that the clamps go on
depends on the diameter of cable. For cables smaller
than 1/2 inch (#16/3 or #12/3), install clamps with the
arrow pointing down. For cables larger than 1/2 inch
(#14/3 or #10/2) install clamps with the arrow pointing
up. Tighten screws evenly until clamp bottoms out. If
required, make bonding connections to the grounding
bar and to external bonding lug.
6. Check tightness of connections, make sure gasket is
properly seated and close the Junction Box with the
screws provided.
NOT LESS THAN 4FT.
TOP FACE OF JUNCTION BOX BASE
JUNCTION BOX
PLUGS
NOT LESS THAN 4”
NOT LESS THAN 8”
DECK
