LIMITED 1 YEAR WARRANTY
If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option,
free of charge. This warranty is extended to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident,
dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified;
(c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs; (f) the finish on any portion of the
product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY
IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL
BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED
WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of pur-
chase, postage prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove,
Illinois 60081-9698/815-675-7000 http://www.intermatic.com Please be sure to wrap the product securely to avoid shipping damage.
158HL13183
THESE INSTRUCTIONS DO NOT COVER ALL VARIATIONS IN EQUIPMENT, NOR DO THEY PROVIDE FOR ALL SITUATIONS
RELATED TO FIXTURE INSTALLATION, OPERATION OR MAINTENANCE. FOR FURTHER INFORMATION CONTACT YOUR
DISTRIBUTOR OR INTERMATIC INCORPORATED - SPRING GROVE, ILLINOIS 60081 (815) 675-7000 www.intermatic.com
MOUNTING & WIRING (continued)
Select appropriate fixture wire to match incoming voltage.
Models FL150MH & FL175MH are shipped with 277 V
wire ready for connections. Models FL150MHT &
FL175MHT are shipped with 347 V wire ready for
connections. If supply voltage is lower, cap wire marked
277 V (or 347 V for tri-tap models) with appropriate twist
on wire connector and strip fixture wire marked with
matching voltage.
Confirm unused voltage fixture wires are appropriately
capped within fixture body.
Feed the matching voltage fixture wire through the
mounting arm.
Replace and secure reflector in the same orientation as
shown in Figure 2.
Close and secure lens door to prevent damage while
wiring fixture to mounting.
Connect the fixture wire matching the incoming voltage
to the black (hot) supply wire.
Connect the fixture wire marked COM to the white
(neutral) supply wire.
Connect the Green (fixture ground) wire to the supply
grounding wire.
Make sure that all wires and connections are inside the
mounting wiring compartment and that the cover is properly
sealed to keep moisture out.
Open lens door. Screw lamp into socket in lampholder until
finger-tight.
Close lens door, making sure that gasket is in place
and compressed to seal out moisture. To weatherproof
fixture, seal all holes in housing (mounting conduit, plugs,
photocontrols, etc.) with silicone sealant.
To operate, restore power to the circuit and switch light on.
c.
d.
e.
f.
g.
h.
i.
j.
3.
4.
5.
6.
AIMING FIXTURE
WARNING
Electric shock hazard.
Do not turn mounting arm more than 360˚ after wires are
connected. Excessive twisting of wires may loosen connections.
Turn off power at circuit breaker or fuse box. Rotate mounting
arm until light is pointing in the desired direction. Tighten
locknut to secure.
Loosen mounting arm bolt (do not remove) and tip fixture to
desired angle. Retighten bolt to secure.
Turn power on and check aim. If adjustment is needed, turn
power OFF at circuit breaker or fuse box and allow fixture to
cool before adjusting
LAMP REPLACEMENT
1. Turn off power at circuit breaker or fuse box. Allow fixture and
lamp to cool.
2. Release retaining clip and swing hinged fixture lens door
open . Remove old lamp and replace with new lamp of correct
type and wattage. Screw lamp into socket in lampholder until
finger-tight.
3. Close and secure lens door, making sure that gasket is properly
seated, free of debris, and compressed to seal out moisture.
4. Turn power back on.
5. Properly dispose of lamp per manufacturer’s recommendations.
1.
2.
3.
FL150MH
(Metal Halide)
Figure 3
277 V
240 V
208 V
120 V
COM
IGN-02
X3
LAMP
X1
X3
COM
CAP
277 V
240 V
208 V
120 V
COM
LAMP
COM
FL175MH
(Metal Halide)
Figure 4
FL150MHT
(Metal Halide
w/tri-tap)
Figure 5
347 V
277 V
120 V
COM
IGN-02
X3
LAMP
X1
X2
COM
CAP
347 V
277 V
120 V
COM
LAMP
COM
FL175MHT
(Metal Halide
w/tri-tap)
Figure 6
CAP
CAUTION
(Metal Halide Lamps Only)
Do not use lamp beyond manufactures rated life to reduce
chance of lamp rupture.Turn lamp off at least once for 15
minutes per week to reduce chance of lamp rupture.
CAUTION
Use lamp of correct type and wattage as specified on fixture.
