MOUNTING & WIRING
1. Loosen (4) screws, and remove fixture lens cover. Set lens cover aside to prevent damage while installing.
(See Figure 2)
2. Loosen (3) screws and remove reflector.
3. Identify supply voltage.
4. Select appropriate fixture wire to match incoming voltage. All fixtures are shipped with 277 V wire ready for
connection. If supply voltage is lower, cap wire marked 277V with appropriate twist on wire connector and strip
fixture wire marked with matching voltage. (See Figure 3)
5. Feed the matching voltage fixture wire, fixture wire marked “COM”, and Green fixture grounding wire out of
the fixture.
6. Confirm all unused voltage fixture wires are appropriately capped within fixture body.
7. Using provided twist on or other approved connectors, connect the fixture wires to the supply wires.
a. Connect the selected voltage fixture wire to the Black (hot) supply wire.
b. Connect the White fixture wire marked “COM” to the White (neutral) supply wire.
c. Connect the Green (fixture ground) wire to the supply grounding wire.
8. Install fixture over mounting. Fixture should be mounted horizontal. (See Figure 2)
9. Install reflector and secure with (3) screws.
10. Screw lamp into lampholder until finger-tight.
11. Install, and secure lens cover with (4) screws making sure that the gasket is properly seated. To weatherproof
fixture, seal all holes in housing (mounting conduit, plugs, photocontrols, etc.) with silicone sealant.
12. To operate, restore power to the circuit and switch light on.
CAUTION:
(Metal Halide Lamps Only) Do not use lamp beyond
manufactures rated life to reduce chance of lamp rupture.
Turn lamp off at least once for 15 minutes per week to reduce
chance of lamp rupture.
LAMP REPLACEMENT
CAUTION:
Use lamp of correct type and wattage as specified on fixture.
1. Turn off power at circuit breaker or fuse box. Allow fixture and lamp to cool.
2. Loosen (4) screws and remove lens cover. Remove old lamp and replace
with new lamp of correct type and wattage. Screw lamp into socket in lampholder until finger-tight.
3. Install and secure lens cover, making sure that gasket is properly seated, free of debris, and
compressed to seal out moisture.
4. Turn power back on.
5. Properly dispose of lamp per manufacturer’s recommendations.
LIMITED 1 YEAR WARRANTY
If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended
to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been
subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs; (f) the
finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES,
INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED
WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage
prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.intermatic.com
Please be sure to wrap the product securely to avoid shipping damage.
THESE INSTRUCTIONS DO NOT COVER ALL VARIATIONS IN EQUIPMENT, NOR DO THEY PROVIDE FOR ALL SITUATIONS RELATED
TO FIXTURE INSTALLATION, OPERATION OR MAINTENANCE. FOR FURTHER INFORMATION CONTACT YOUR DISTRIBUTOR OR
INTERMATIC INCORPORATED - SPRING GROVE, ILLINOIS 60081 (815) 675-7000 www.intermatic.com
158HL12760
Metal Halide 150 Watt
Figure 3
277 V
240 V
208 V
120 V
COM
IGN-01
X3
LAMP
X1
X3
COM
CAP
