Interlogix IFS MC352-4P-2S Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 31

Interlogix IFS MC352-4P-2S Скачать руководство пользователя страница 20

- 20 -



Link status auto detect and redundant on Dual ports with same connector type.



Only Primary-Port is active at a time, the Backup-Port is blocked.



When Primary-Port link failure occurs, the traffic swaps to Backup-Port automatically.



Once the Primary-Port status is back to link up, the traffic will swap from Backup-Port to

Primary-Port.

2.2 Mounting Installation

This section describes how to install the Industrial Gigabit PoE+ Switch and make connections to it.

Please read the following topics and perform the procedures in the order being presented.

In the installation steps below, this Manual uses IGS-801 (IFS 8 Port Industrial Gigabit
Switch) as the example. However, the steps for IFS Industrial Gigabit PoE+ Switch are
similar.

2.2.1 DIN-Rail mounting

The DIN-Rail is screwed on the Industrial Gigabit Ethernet Switch when out of factory. When needed to

replace the wall mount application with the DIN-Rail application on Industrial Gigabit Ethernet Switch,

please refer to the following figures to screw the DIN-Rail on the Industrial Gigabit Ethernet Switch. To

hang the Industrial Gigabit Ethernet Switch, follow the steps below:

Step 1:

Screw the DIN-Rail on the Industrial Gigabit Ethernet Switch.

«
...
18
19
20
21
22
...
»

Содержание IFS MC352-4P-2S
































Отзывы:

Нет отзывов