Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 376

background image

Chapter 5: Menu reference

188

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

Note:

If zones are assigned to more than one area, the longest prealarm time is

used. See “4 Zones and areas” on page 171.

4.2.n.4.3 Unset delay

3 Unset delay
> <

Set a delay for authorized unset (in minutes). The allowed range is 1 to 30 min.

0 means that no delay is applied. See “Delayed unset” on page 52 for more

details.

4.2.n.5 Set/unset options

1>Entry alarms
Delayed

The menu groups the following setting options.

4.2.n.5.1 Entry alarms

1 Entry alarms
>Delayed<

The Entry alarms option defines whether the entry fail alarm is reported

immediately. The following values are applicable:
• Delayed: The alarm activates 30 s after the entry time passed.
• Instant: The alarm activates immediately.

4.2.n.5.2 Set retry

2 Set retry
>Off<

Set retry defines whether users can postpone or cancel an autoset. If this option

is set to On, you can postpone autoset during the Warning time (see “4.2.n.4.1

Warning time” on page 187). If the autoset has been postponed by a normal

user, the system will attempt autoset again after a time period defined in “8.4.8

AS user retry” on page 245.

Note:

The privileged users, Installer and Supervisor, can choose the postpone

time during the Warning time.

4.2.n.5.3 Silent autoset

3 Silent autoset
>Off<

If Silent autoset is on, the keypad buzzer remains silent during the “4.2.n.4.1

Warning time” described on page 187.

«
...
192
193
194
195
196
...
»

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATS1500A-IP-LP

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 6

Бренд: Omegalink Страницы: 2

Бренд: Watts Страницы: 4

Бренд: phytron Страницы: 55

WisBlock RAK19012

Бренд: RAK Страницы: 12

Бренд: zeeltronic Страницы: 15

Бренд: M-system Страницы: 3

Бренд: zeeltronic Страницы: 13

Бренд: QD Dynamics Страницы: 64

Cutler-Hammer S701X25N3BP

Бренд: Eaton Страницы: 4

Бренд: C&C Страницы: 17

PMC-BiSerial-III SDLC

Бренд: Dynamic Engineering Страницы: 37

Бренд: Bartington Страницы: 21

Бренд: HABONIM Страницы: 18

Бренд: ADLINK Technology Страницы: 311

Бренд: Tascam Страницы: 14

Бренд: Wecon Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды