Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 376

Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 152

Chapter 5: Menu reference

146

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

• Card or PIN: Either a PIN or a card is required to set or unset

2.2.1.n.3.7.2 Logoff time

2 Logoff time
>3<

A time period (in minutes) of the keypad inactivity before the user is automatically

logged off.
Allowed range is 1 to 255 minutes. Default value is 3.

2.2.1.n.3.7.3 1 x set/unset

3 1xset/unset
>Off<

One-time badge to set/unset defines if the selected keypad allows you to set or

unset areas with one badge. The following values are available:
•  Off: One badge does not cause any set or unset action.
•  Unset: One badge unsets areas.
•  Set-Unset: One badge sets or unsets areas.
•  Part set 1-unset / Part set 2-unset: One badge partially sets or unsets areas.

2.2.1.n.3.7.4 3 x badge set

4 3xbadge set
>Off<

Three-time badge to set defines if the selected keypad allows you to set areas

with triple badge. The following values are available:
•  Off: Triple badge does not cause any action.
•  Set: Triple badge sets areas.
•  Partset1 / Partset 2: Triple badge partially sets areas.

Notes

• This functionality works only if areas can be set with a card. See

“2.2.1.n.3.7.1 Card&PIN mode” on page 145 for available modes.

• This functionality is available only if the “2.2.1.n.3.7.3 1 x set/unset” option

described above is not configured as Set-Unset.

2.2.1.n.3.8 EE PIN lock

8 EE PIN lock
>No<

If the EE PIN lock option is set to Yes, it is not possible to use a PIN during the

entry time.

«
...
150
151
152
153
154
...
»

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды