Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 108

Страница: 108 / 376

Chapter 3: System functions

102

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

Engineer reset

Some events can be set to require an engineer reset to be performed. The

engineer reset can be done in one of the following ways:
• The engineer (installer) performs an engineer reset from the Engineer menu.

See “8.2.4.13 Do reset” on page 239.

• The user enters a reset code.

In case an engineer reset is required, an engineer code is displayed.

Eng. reset
Code:23353

In this case the user contacts the engineer (installer) and gives him the

engineer code displayed. Using this code and the system code defined in the

menu “8.2.4.12 System code” on page 239, the installer calculates a reset

code, which he gives to the user. The user enters the calculated code and

performs an engineer reset after logging in.

Note:

If System code is not defined, the engineer reset by user is not

available.

• The reset is performed by an activation of the special Engineer reset zone

type (see “4.1.n.2 Zone type” on page 172). This is used in systems using

RedCare transmitters, where the central station operator can switch an output

that is wired back into the panel to perform an engineer reset.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды