Interlogix 60-660-43 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 10

Interlogix 60-660-43 Скачать руководство пользователя страница 8

8 / 10

P/N 466-1452

• REV E • ISS 16OCT18

Figure 10: N/C loop wiring diagram

Figure 11: Nonsupervised loop wiring diagram shows a
wiring diagram for a nonsupervised loop.

Figure 11: Nonsupervised loop wiring diagram

Figure 12: Relay wiring diagram shows a wiring diagram
when using a relay.

Note:

The 12 VDC relay coil resistance must be at least

300 ohms.

Figure 12: Relay wiring diagram

RF reception test

You can test the receiver by either counting the LED flashes
when transmitters are tripped, or by counting the beeps
emitted by an attached piezo beeper (optional).

To test the system using the receiver LED, do the following:

1. Make sure the DIP switch is down (normal operation/run

mode).

2. Trip all sensors in the system. After each trip, watch for

the correct number of LED flashes as indicated in
Table 3.

Table 3: LED/piezo test responses

Transmitter

Should cause

Sensors

7 to 8 beeps and LED flashes

Keypad
touchpads

1-button press

2 beeps and LED flashes

2-button press

8 beeps and LED flashes

To test the system using a piezo beeper, do the following:

1. Connect a piezo beeper between the test output (T) and

ground (GND) as shown in Figure 13: Piezo status
beeper connections.

Figure 13: Piezo status beeper connections

2. Make sure the DIP switch is down (normal operation/run

mode).

3. Trip all sensors in the system. After each trip, listen for

the correct number of beeps from the piezo beeper as
indicated in Table 3.

Securing the cover

To help prevent accidental tamper alarms caused by cover
removal, install the two self-tapping screws (included) on top
of the cover (Figure 14: Cover screws).

Receiver terminals

Zone 1

Return

Panel GND

Panel +12V

Receiver terminals

Panel terminals

Zone 1

Return

Panel GND

Panel +12V

EOL resistor

Receiver terminals

Panel terminals

Zone 1

Return

Panel GND

Panel +12V

N/O

COM

N/C

Coil

Coil

Receiver terminals

Panel terminals

«
...
6
7
8
9
10
»

Содержание 60-660-43











Отзывы:

Нет отзывов