Interfacion QED-PL2 Скачать руководство пользователя | Manualshive

Страница: 29 / 35

background image

29

HOW TO SEARCH THE GROUND

Turn the detector

ON

and

GROUND BALANCE

, then complete the set-up procedure as shown

above.

Lower the detector coil to the ground and move slowly forward, swinging the detector from side to
side parallel but just clear of the ground.

Sweep the coil in a wide arc without lifting the coil at the end of each arc. Overlap each swing over
the previous arc to ensure you do not miss any targets.

When a target is identified swing the coil over the target in one direction, then repeat again at right
angles to confirm target and location. A good target will produce a clear repeatable signal.

Dig out your target and remember to refill your excavation on completion.

«
...
27
28
29
30
31
...
»

Содержание QED-PL2




































Отзывы:

Нет отзывов

Похожие инструкции для QED-PL2

Бренд: Minelab Страницы: 2

Бренд: RIDGID Страницы: 103

GENESIS-II DIRECTIONAL

Бренд: Decatur Electronics Страницы: 90

Бренд: DeepTech Страницы: 19

Бренд: RKI Instruments Страницы: 98

Бренд: Uniden Страницы: 25

Бренд: Inficon Страницы: 16

Бренд: K40 Страницы: 2

Бренд: HIKVISION Страницы: 8

8000 Gas Stop GPL 08496

Бренд: Vimar Страницы: 128

Бренд: Industrial Scientific Страницы: 48

Бренд: Industrial Scientific Страницы: 89

Ventis Pro Series

Бренд: Industrial Scientific Страницы: 110

GasBadge Plus 3.0

Бренд: ISC Страницы: 43

GASALARM S/200-P

Бренд: AMS Страницы: 28

Бренд: Minelab Страницы: 12

Бренд: Whistler Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды