Interactive Technologies Commander 2000 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 61

Interactive Technologies Commander 2000 Скачать руководство пользователя страница 39

39

S E C T I O N 5 –

MAINTAINING YOUR SYSTEM

Follow these maintenance procedures to help keep your system reliable and trouble-free.

Required System Tests

It is important that you check the system status and perform phone and sensor tests
weekly. These procedures ensure that your system is fully operational.

■

To check system status:

With all sensors in their normally secure position, press

STATUS.

The panel and interior sirens sound arming level beeps, corresponding to the current
arming level. The panel announces system status, as shown in Table 8.

NOTE:

If a sensor is open, the system announces only the open sensor
number. The status of the backup battery and AC power are
announced only if there is a problem.

■

To perform a phone test:

NOTE:

Performing a phone test is only necessary if your security system is
monitored by a monitoring service.

Table 8

. Voice Status Messages

Main Message

Status

Level

Alarm System is

OFF

—

ON

Level 2

ON

Level 3

System Battery

is OK.

—

Failure

†

—

AC Power

is OK.

—

Failure

‡

—

†

See "Replacing Panel Backup Batteries" on page 41.

‡

Check if the AC power transformer is plugged in. Check the cir-

cuit breaker or fuse controlling the outlet. If you still don’t have
AC power, contact your security consultant.

Technical Manuals Online! - http://www.tech-man.com

«
...
37
38
39
40
41
...
»

Содержание Commander 2000






























































Отзывы:

Нет отзывов