Intelligent Motion Systems MDrive DSP-402 Скачать руководство пользователя

Страница: 36 / 64

MDrivePlus CANopen R020507

Object 6040

— Controlword

Ths controlword is a mandatory, unsigned 16 bit number containing bits for controlling the state and operating modes for the MDrivePlus

CANo-

pen

Object Description

Index

6040

Name

Controlword

Object Code

VAR

Data Type

Unsigned16

Entry Description

Access

r/w

PDO Mapping

n/a

Range

Unsigned16

Default

n/a

Data Description

MSB

LSB

Manufacturer

Specific

Reserved

Halt

Fault

Reset

Operation

Mode Specific

Enable

Operation

Quick

Stop

Enable

Voltage

Switch

O=Optional M= Mandatory

Device Control Command Bit Patterns (Bits 0-3 and 7)

Command

Bit of Controlword (6040h)

State

Transitions

Fault Reset

(Bit 7)

Enable

Operation

(Bit 3)

Quick Stop

(Bit 2)

Enable

Voltage

(Bit 1)

Switch On

(Bit 0)

Shutdown

2, 6, 8

Switch On

Disable Voltage

7, 9, 10, 12

Quick Stop

7,10, 11

Disable Operation

Enable Operation

4, 16

Fault Reset

*The MDrivePlus CANopen executes the functionality of Switched On

** The MDrivePlus CANopen will do nothing

Table 4.3: MDrivePlus CANopen Device Control Commands (Bits Marked X are not relevant)

Device Operation Mode Bit Patterns (Bits 4-6 and 8)

Operation Mode

Controlword 6040h Bits 4-6, 8

Bit 8

Bit 6

Bit 5

Bit 4

Profile Position

Halt

Absolute/Relative

Change Set Immediately

New Setpoint

Profile Velocity

Halt

Reserved

Homing*

Halt

Homing Operation Start

Reserved

*Homing Mode is currently under development for the MDrivePlus

CANopen

Table 4.4: MDrivePlus CANopen Operation Modes

Содержание MDrive DSP-402

































































Результаты поиска

Содержание MDrive DSP-402

Отзывы:

Похожие инструкции для MDrive DSP-402

Бренды по названию

Популярные бренды

Intelligent Motion Systems MDrive DSP-402, Инструкция по применению

Результаты поиска

Содержание MDrive DSP-402

Отзывы:

Похожие инструкции для MDrive DSP-402

Бренды по названию

Популярные бренды