Intel Stratix 10 Скачать руководство пользователя страница 29

Страница: 29 / 228

Parameter

Value

Description

• TX/RX Duplex: Specifies a single channel that supports

both transmission and reception.

The default is TX/RX Duplex.

Number of data channels

1-24

Specifies the number of transceiver channels you want to

implement. The default value is 1. The maximum value is

24.

Enable RSFEC

On/Off

Enables the RS-FEC functionality.

(

)

Provide separate interface

for each channel

On/Off

When selected, the Native PHY IP core presents separate

data, reset, and clock interfaces for each channel rather

than a wide bus.

Enable datapath and

interface reconfiguration

On/Off

Enables the ability to preconfigure and dynamically switch

between the RS-FEC enabled and disabled modes.

Number of reference clock

inputs

1-5

(

)

Specifies the desired number of reference clocks intended

for the transmitter AND/OR receiver. This allows for

dynamic clock source switching. Native PHY IP Core allows

up to five clock inputs out of the possible nine for dynamic

clock switching.

Initial TX reference clock

input selection

This indicates the starting clock input selection used for

this configuration when dynamically switching between

multiple clock inputs.

Enable dedicated RX

reference clock input

On/Off

Option to assign dedicated reference clock for the receiver

instead of sharing it with the transmitter.

Dedicated RX clock input

selection

0-4

When you enable the Enable Receiver dedicated

reference clock input option, you can select the input

clock with this parameter.

2.2.2. PMA Parameters

You can specify values for the following types of PMA parameters:

TX PMA:
•

TX PMA Options

•

TX PMA Pre-equalization

•

TX Clocking Options

RX PMA:
•

RX PMA Options

•

RX PMA Optional Ports

•

RX Clocking Options

(2)

When you enable RS-FEC, the number of data channels is 1-4.

2. Implementing the Transceiver PHY Layer in Intel Stratix 10 Devices

UG-20056 | 2019.02.04

Send Feedback

Intel

Stratix

10 E-Tile Transceiver PHY User Guide

Содержание Stratix 10





































































































































































































































Результаты поиска

Содержание Stratix 10

Отзывы:

Бренды по названию

Популярные бренды

Intel Stratix 10, Руководство пользователя

Результаты поиска

Содержание Stratix 10

Отзывы:

Бренды по названию

Популярные бренды