Intel Stratix 10 страница 21 Скачать руководство пользователя

Страница: 21 / 228

1.4.5. Supported Applications/Modes

Table 6.

Supported Applications/Modes

Supported

Application/Mode

EHIP_CORE

EHIP_LANE

PMA Direct

RS-FEC

Dual Mode

(1)

PAM4/NRZ

100GbE (4 x 25G) –

NRZ w/ FEC

Yes

Yes (Aggregate)

NRZ

100GbE (2 x 50G) –

PAM4 w/ FEC

Yes

Yes (Aggregate)

Yes

PAM4

100GbE (4 x 25G) –

NRZ w/o FEC

yes

NRZ

32G Fibre Channel w/

FEC

Yes

Yes (Fractured)

NRZ

25GbE - NRZ w/FEC

Yes

Yes (Fractured)

NRZ

25GbE - NRZ w/o FEC

Yes

NRZ

CPRI 24G - NRZ w/

FEC

Yes

Yes (Fractured)

NRZ

10GbE – NRZ

Yes

NRZ

NRZ - 1G to 30G

Yes

NRZ

PAM4 - 2G to 30G

Yes

PAM4

PAM4 - 30G to 57.8G

Yes

PAM4

NRZ - 1G to 30G w/

FEC

Yes

Yes (Fractured)

NRZ

1.4.6. Feature Comparison Between Transceiver Tiles

Table 7.

Transceiver Tile Feature Comparison

Feature

L-Tile/H-Tile

E-Tile

Native PHY IP

Configure NRZ mode

Configure NRZ and PAM4

PLL IP

ATXPLL, fPLL and CMU PLL IPs (available in the

IP catalog)

Embedded in Native PHY and Ethernet Hard

IPs

Reset controller IP

Reset controller IP (available in the IP catalog)

Embedded in the Native PHY and Ethernet

Hard IP cores

Clocking modes

• TX PMA bonding up to 24 channels
• ATXPLL-fPLL and fPLL-fPLL cascade
• VCXO replacement (ATXPLL and fPLL

fractional division support)

Only TX PMA bonding supported

Calibration

Power-up calibration and recalibration

Configuration ports

For each instantiated IP (Native PHY IP core,

ATXPLL/fPLL), there is one configuration port.

For each instantiated Native PHY IP core,

there are two configuration ports: one for the

Native PHY IP core and another for RS-FEC.

continued...

(1)

PMA Direct high data rate mode

1. Intel

Stratix

10 E-Tile Transceiver PHY Overview

UG-20056 | 2019.02.04

Send Feedback

Intel

Stratix

10 E-Tile Transceiver PHY User Guide

Содержание Stratix 10





































































































































































































































Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды

Intel Stratix 10, Руководство пользователя

Результаты поиска

Содержание Stratix 10

Отзывы:

Похожие инструкции для Stratix 10

Бренды по названию

Популярные бренды