background image

18

Intel® RAID Controller SRCSASLS4I Hardware User’s Guide

Additional safety guidelines:

When you disconnect a cable, pull on its connector or on its strain-relief loop, not on 
the cable itself. Some cables have a connector with locking tabs; if you are 
disconnecting this type of cable, press in on the locking tabs before disconnect the 
cable. As you pull connectors apart, keep them evenly aligned to avoid bending any 
connector pins. Also, before you connect a cable, make sure both connectors are 
correctly oriented and aligned.

Handle components and cards with care. Don't touch the components or contacts on 
a card. Hold a card by its edges or by its metal mounting bracket. Hold a component 
such as a microprocessor chip by its edges, not by its pins.

Protecting against electrostatic discharge

Static electricity can harm delicate components inside your computer. To prevent 
static damage, discharge static electricity from your body before you touch any of 
your computer's electronic components, such as the microprocessor. You can do so 
by touching an unpainted metal surface, such as the metal around the card-slot 
openings at the back of the computer.

As you continue to work inside the computer, periodically touch an unpainted metal 
surface to remove any static charge your body may have accumulated. In addition to 
the preceding precautions, you can also take the following steps to prevent damage 
from electrostatic discharge (ESD):

When unpacking a static-sensitive component from its shipping carton, do not 
remove the component from the antistatic packing material until you are ready to 
install the component in your computer. Just before unwrapping the antistatic 
packaging, be sure to discharge static electricity from your body.

When transporting a sensitive component, first place it in an antistatic container or 
packaging.

Handle all sensitive components in a static-safe area. If possible, use antistatic floor 
pads and workbench pads.

Содержание SRCSASLS4I - RAID Controller





































Отзывы: