Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 47

Страница: 47 / 162

Intel

Server System SR2612UR Service Guide

Installing the Disk Drives

Caution: Before installing new disk drives, acclimate them to room temperature. Store drives at

room temperature for two hours prior to use.

Note: To install a disk drive or plastic blank into a carrier, refer to

“Drive Installation in the

Drive Carrier” on page 75

in this manual.

1. Select an open drive slot.

2. Hold the disk drive so the LEDs are on the left and the lever is fully open.

3. Slide the disk drive into the drive slot until the lever starts to close.

Figure 24. Sliding the Disk Drive into the Drive Slot

4. Push the lever until it meets the latch on the left side of the drive slot and clicks into

place.

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды