Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 100

Страница: 100 / 162

Intel

Server System SR2612UR Service Guide

Figure 79. LED Board

The following table describes the LED Board LEDs.

Monitoring the Disk Drives

Each populated disk drive carrier has three LEDs that indicate the status of the disk drive,
as described in the following table.

Figure 80. Disk Drive LEDs

Table 5. LED Board LEDs Descriptions

LED

Color

Description

Standby Power OK

Green

Indicates the power is okay

System Status
LED Green

Green

System Status
LED Amber

Amber

System Identify

Blue

Enclosure ID

Table 6. LED Status for the Disk Drive

LED

Condition

Color

Not Used

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды